Novoferm iso70-1 serie Montage-, Bedienungs- Und Wartungsanleitung Seite 11

GB
GB
Door frame preassembly [1.10],
Lay wood or similar protective material (to guard against
(1)
scratches) under the angular frames 1
frame 1 + frame panel 3 + angular frame 1
R
(tapping screws are pre-assembled)
plate 4 /4 to the top corner using S11
R L
For rebate width 35 – 119mm: S5 through the rectangular
hole in the 16 /16 moulded end piece and top corner, and
R L
use S12 to prevent it from falling out
Note! If using a window as the top section, we recommend
taking the panel seal from frame panel 3 and turning it 180
degrees (see label on window).
(2) Depending on rebate width and plug points, bolt wall anchor
7 to angular frame 1
(2a) Rebate wider than 120mm - Variant 1:Wall anchor 7
facing outwards
Rebate width 35 - 119mm wide - Variant 2: Wall
(2b)
anchor 7 facing inwards
If using other
absorption capacity is at least equal to that of the wall
anchors supplied 7.
Door frame installation [1.15],
(3) Rest door frame against garage opening, secure against
tipping, use a spirit level to ensure exact parallel and
angular alignment. Clip panel holder 13 to centre of panel 3.
Scope of supply includes 2 panel holders for BRB 3530mm
or more. Mount complete angle frames with S8 + S9
. Fix the base of the frame using bolts S8 + S9
c, d] [2.10 a]
and washer U1.
[1.15b]
frames 1 /1 are not twisted or bent during this process;
R L
provide suitable underlay before tightening the screws!!!
VL: Minimum distance between upper edge of frame and
ceiling = 5mm!!!
Horizontal track pairs preassembly [1.20],
(4) Bolt right 14 or left 14
R
corresponding moulded end piece 16
connecting plate 18 using (S6 + S12)
track mounting bracket 19
connecting angle 20
plate 21 /21 + fastening profile 100 (S6 + S12)
R L
Horizontal track pairs pre-assembly [1.25],
(5) Assemble anchor tracks 27
(5a) For interior garage widths max. BRB + 1030mm
(when installing door in the middle): insert one
anchor track 27 each right and left in track connector
6 and bolt to clip plate 29 and connecting bracket 28
with S6 + S12 making sure they can still be pulled
out .
[1.25 a,b]
(5b) For interior garage widths greater than BRB +
1030mm and HL installation: track connector 6 is
fixed later to the ceiling.
Bolt the horizontal track pairs 14
to top corner
making sure they can still be folded up afterwards

Rebate wider than 120mm: Insert S5 through the
rectangular hole in the 16
top corner, and tighten by hand using S12.
(6) Bolt track connectors 6 each with two S6 + S12 to the VL
corner connecting angles 20
connectors 6 each with two S6 + S12 to the HL sole plate
.
21 /21
[2.10 e]
R L
Hanging horizontal track pairs [1.30],
Keep these installation, operating, and maintenance instructions in a safe place during the entire service life of the garage door!
[2.10]
/1 . Bolt angular
R L
. Bolt VL sole
[1.10 a]
.
[1.10 b]
.
[1.10 cb]
/1 using S6 + S12.
R L
.
[ 1.10 ca ]
.
[ 1.10 ca ]
fasteners, make sure
[2.10]
. Caution: Make sure the angle
[2.10]
horizontal track pairs with
L
/16
R L
[1.20 a, b]
. Bolt VL corner
[1.20 ca, cb]
/20 (S6 + S12) .
[1.20 d]
R L
[2.10]
at moulded end piece 16
/14
R L
[1.25 c]
/16 moulded end piece and
R L
.
/20
[1.25 d]
R L
[2.15]
(7) Fold up horizontal track pairs 14
falling (safely prop up track connectors 6).
(8) Bolt the track arcs 30 using S15 + S12 to angular frames
1 /1
together R
L
smooth transition to track profiles, use plumber's
wrench to adjust the ends if necessary).
(9) Bolt the moulded end piece 16
[1.30 a]
(10) Bolt the HL upper deflection pulley bracket 101
through the top corner to moulded end piece 16
fastening profile 100 using S11
(11) Use a spirit level to make sure track connectors 6 and
horizontal track pairs 14
wall or ceiling. Do not tighten the screws yet; you may need
to realign.
(11a) VL wall fastening: Bolt connecting bracket 28 + 2x S8
(11b) Ceiling fastening: Anchor track 27 + connecting
their load
Fasten track mounting bracket 19 and connecting plate 18
to the ceiling, together with the anchor tracks 27 +
connecting bracket 28 + S6 + S12 + 2x S8 + S9
Caution: From BRB 3530mm and from BRH 2126mm,
mount additional ceiling brackets to track connector 6.
Anchor tracks 27 + connection bracket 28 + clip plate 29
+ S6 + S12 + 2x S8 + S9)
Mounting torsion spring [1.35];
(12) Insert pre-assembled right torsion spring 35
[1.15 a,
and fasten with S11
+ S9).
Insert 2x S5 screws through clip plate 29 and into track
connector 6. Pre-assemble centre bearing 37 and base
plate 103 using S6 + S12 and use S12 to bolt to clip plates
29
[2.15 da, db]
into HL sole plate 21
Attach ceiling mount to centre bearing 37 (anchor tracks 27
+ connecting bracket 28 + S6 + S12 + S8 + S9)
+ S15 and
Mount 1 centre bearing 37 on garage doors widths up to
. Open up
BRB 3529mm (a>120mm).
Mount 2 centre bearings 37 on garage doors widths from
Bolt HL sole
BRB 3530mm. Same procedure with 2nd bearing on left
.
spring. Make sure centre bearings are exactly aligned to
[2.10 c,d,e]
ensure smooth operation. Plug the coupling 38 onto shaft
end and assemble left torsion spring 35
procedure as for right torsion spring 35
to the centre over the shaft ends and tighten gently by hand.
[1.35 c]
Installing door leaves [1.40]; [1.45]; [1.50]; [1.55]; [2.20].
(13) Bottom section 44 (B)
(13a) Slide floor seal 47 (2x) into floor track 67 and insert
/16
R L
(13b) Attach logo
.
(14) Before inserting bottom section 44, use a damp cloth to
clean angular frames 1
between angular frames 1
Insert roller 56 into universal hinge 48 and install universal
hinge 48 on bottom section 44 with S3 (MA=10 Nm)
Bolt track
(14a) Unroll cable 104 from torsion spring 35
(14b)
- 9 -
and connecting plates 18
L
/14L are horizontal, and fasten to
R
+ S9
[1.30 b]
bracket 28 + S6 + S12 + 2x S8 + S9
Diagonal reinforcement can be added to enhance
stability. .
;
[1.30 d] [2.15 c]
[1.30 g]
[2.15]
. Mount centre bearing 37 (S8
[1.35 aa, ab]
;
[1.35 b, da, db]
. Insert pre-assembled right torsion spring 35
/21 and fasten with S11
R L
; .
[2.15 h]
rubber end plugs 45 /45
R
67 + S3 to bottom section 44
open the protective foil around an end cap and
remove . Bolt floor handle 49 using S3 to
[1.40 ca, cb]
bottom section .
[1.40 e]
.
[1.40 d]
/1
[1.30]
R L
/1
R L
guide behind roller 56
[1.45 b]
Unroll and remove cable 104 from HL torsion spring
35 /35 ; these are no longer required
R L
/14 and secure against
R L
(ensure
[1.30 a]; [2.15 a]
to top corner using S11.
R/L
/101
R
and
/16
R L
.
[2.15 a]
;
[1.30 c] [2.15b]
[1.30 e+f]
in sole plate 4
R
[2.15 e, f]
.
[2.15 g]
using the same
L
. Slide coupling 38
R
. Fasten floor track
[1.40 a]
L
. Carefully cut
[1.35b]
. Position bottom section 44
and secure against falling.
[1.45a,b]
/35 and
R L
.
. Bolt the
[2.15 i]
L
.
.
R
R
.
.