Homelite HCS5150C Übersetzung Der Originalanleitung Seite 32

Deutsch (Übersetzung der originalen Anleitungen)
WARNING
Never climb into a tree to limb or prune. Do not stand on
ladders, platforms, a log, or in any position which may
cause you to lose your balance or control of the saw.
■ When pruning trees it is important not to make the
flush cut next to the main limb or trunk until you have
cut off the limb further out to reduce the weight. This
prevents stripping the bark from the main member.
1. Underbuck the branch 1/3 through for your first cut (A).
2. Overbuck the branch to drop it (B).
3. Finish by cutting smoothly and neatly against the main
member (C) so the bark will grow back to seal the
wound.
WARNING
If the limbs to be pruned are above chest height, hire a
professional to perform the pruning.
CUTTING SPRING POLES
See figure 37.
A spring pole (A) is any log, branch, rooted stump, or
sapling which is bent under tension by other wood so that
it springs back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of
springing back to the upright position during the bucking
cut to separate the log from the stump. Watch out for
spring-poles; they are dangerous.
WARNING
Spring poles are dangerous and could strike the
operator causing the operator to lose control of the
chainsaw. This could result in severe or fatal injury to
the operator.
MAINTENANCE
ASSEMBLING THE BAR AND CHAIN
See figure 3. See figure 38 - 47.
DANGER
Never start the engine before installing the guide bar,
chain, drivecase cover, and clutch drum. Without all
these parts in place, the clutch can fly off or explode,
exposing the user to possible serious injury.
English (Original instructions)
To avoid serious personal injury, read and understand
all the safety instructions in this section.
1. Always place the switch in the stop "O" position before
2. Make sure the chain brake is not set by pulling the
3. Wear gloves when handling the chain and bar. These
4. Remove the bar mounting nuts using a combination
5. Remove the clutch cover (D), and the outer guide bar
6. Lay out the new saw chain in a loop and straighten any
7. Place the chain drive links into the bar groove.
8. Position the chain so there is a loop at the back of
9. Hold the chain in position on the bar and place the loop
10. Fit the bar flush against the mounting surface so that
11. Replace the outer guide bar plate ensuring that the bar
12. Replace the clutch cover and bar mounting nuts.
13. Tighten the bar mounting nuts finger tight only. The bar
14. Remove all slack from the chain by turning the chain
15. Lift the tip of the guide bar up to check for sagging (N).
16. Release the tip of the guide bar and turn the chain
17. Hold the tip of the guide bar up and tighten the bar
The chain is correctly tensioned when there is no sagging
on the underside of the guide bar, the chain is snug, but
can be turned by hand without binding. Ensure that the
chain brake is not set.
NOTE: If chain is too tight, it will not rotate. Loosen the
bar nuts slightly and turn the tension adjuster 1/4 turn
anticlockwise. Lift the tip of the guide bar up and retighten
the bar nuts securely. Ensure that the chain will rotate
30 30
WARNING
you work on the saw.
chain brake lever/hand guard towards the front handle
to the run position.
components are sharp and may contain burrs.
wrench or a 5/8 inch spanner.
plate (E).
kinks. The cutters should face in the direction of chain
rotation. If they face backwards, turn the loop over.
the bar.
around the sprocket.
the bar studs are in the long slot of the bar.
NOTE: When placing the bar on the bar studs ensure
that the adjusting pin (L) is in the chain tension pin
hole.
pin groove is at the bottom with the upper and lower
edges angled away from the guide bar.
must be free to move for tension adjustment.
tensioning screw (M) clockwise until the chain seats
snugly against the bar with the drive links in the bar
groove.
tensioning screw 1/2 turn clockwise. Repeat this
process until sagging does not exist.
mounting nuts (O) securely.