Troubleshooting; Technical Specification - Hallde VCM-41 Bedienungsanleitung

the outside.
If the electric cable is damaged or cracked,
or if any of the above safety functions does
not perform as intended, get a specialist to
look at the machine before using it again.
That all visible screws and bolts are securely
tightened.
That the blades of the cutter (H) are in good
condition and have sharp edges.
TROUBLE-SHOOTING
FAULT: The machine cannot be started, or
stops while in operation and cannot be
restarted. REMEDY: Check that the plug is
securely fitted into the power supply socket
or that the safety isolating switch is in position
"I". Fit the bowl (I) and lid (A) correctly. Move
the safety arm (K) all the way over the centre
of the lid. Check that the fuses in the fuse box
for the premises have not blown and that
they have the correct rating. Wait for a few
minutes and try to restart the machine. If the
machine still fails to run, call a specialist.
FAULT: Low capacity or poor cutting results.
REMEDY: Make sure that the blades are in
good condition and are sharp. Cut the food
to be processed into smaller pieces of equal
size. Process the food for a shorter or longer
time. Process smaller quantities at a time.
Always have the scraper (C) fitted and use it
whenever necessary.

TECHNICAL SPECIFICATION

OF THE VCM-41
Machine base: Motor: 450 W, 100 V, single
phase, 50/60 Hz, 9/8 A.
Motor: 550 W, 1 10-120 V, single phase,
50/60 Hz, 8 A.
Motor: 550 W, 230 V, single phase, 50/60
Hz, 4.7 A.
Thermal motor protection. Transmission: direct
drive. Safety system: three individual safety
switches and mechanical motor brake.
Degree of protection: IP44. Plug: 10 A,
earthed. Fuse in fuse box for the premises: 10
A, slow-blow. Sound level LpA (EN31201):
72 dBA. Magnetic field: less than 0,1
mikrotesla.
Controls and speeds: "0" = machine
switched off. "I" = machine runs continuously
at 1500 rpm (50 Hz) or 1700 rpm (60 Hz).
"P" (pulse) = machine runs at 1500 rpm (50
Hz) or 1700 rpm (60 Hz) until the knob is
released.
Bowl volume: Gross volume 4 litres. Net
volume liquid 1.6 litres.
Net weights: Machine base: 14,8 kg. Bowl
complete with knife, lid and scraper system:
1,6 kg.
Materials: Machine base of aluminium.
Bowl* of stainless steel. Cutting unit* with
center hub of acetal and knives of of high
quality Swedish steel. Lid* and scraper
system* of genuine polysulfon. * = Can be
machine washed.
Norms: EU Machine directive 89/392/EEC.
EMC Directivektive 89/336/EEC.
TECHNICAL SPECIFICATION
OF THE VCM-42
Motor: 750/370 W, 230 V, three phase,
50 Hz, 2,5/2,0 A.
Motor: 750/370 W, 400 V, three phase,
50 Hz, 1,7/1,4 A.
Thermal motor protection. Transmission: direct
drive. Safety system: three individual safety
switches and mechanical motor brake.
Degree of protection: IP44. Plug: 16 A,
earthed. Fuse in the fuse box for the premises:
10 A, slow blow. Sound level LpA
(EN31201): 72 dBA. Magnetic field: less
than 0,1 mikrotesla.
Controls and speeds: "0" = machine
switched off. "I" = machine runs continuously
at 1500 rpm. "II" = machine runs
continuously at 3000 rpm. "P" (Puls) =
machine runs at 3000 rpm until the knob is
released.
Bowl volume: Gross volume 4 litres. Net
volume liquid 1.6 litres.
Net weights: Machine base: 15,4 kg. Bowl
complete with knife, lid and scraper system:
1,6 kg.
Materials: Machine base of aluminium.
Bowl* of stainless steel. Cutting unit* with
center hub of acetal and knives of of high
quality Swedish steel. Lid* and scraper
system* of genuine polysulfon. * = Can be
machine washed.
Norms: EU Machine directive 89/392/EEC.
EMC Directivektive 89/336/EEC.