Setting The Speed (Figure O); Rollover (Figure P); Calibration; Recording Data (Figure U) - lidl 284749 Gebrauchsanweisung

• Non-head mode
This is a flying aid that always makes the
quadrocopter (1) fly in the instructed direction
as soon as it is activated and it is recommen-
ded for pilots with little flying experience. For
example the quadrocopter (1) always flies right
from the pilot's point of view if you press the
button (2g) on the non-head mode and steer to
the right with the joystick (2f) – whether or not
the front of the quadrocopter (1) (camera lens)
is pointing backwards, to the left, forwards, or
to the right. If this mode is de-activated then the
quadrocopter (1) flies in the direction in which
the front (camera lens) is pointing (even if the
quadrocopter (1) has changed direction).
PLEASE NOTE: The remote control (2)
and the quadrocopter (1) must be aligned
exactly the same way when the non-head mode is
activated! Only activate the non-head mode in the
given position or the controls may not be carried
out correctly.
1. In order to activate the non-head mode place
the quadrocopter (1) and the remote control
(2) behind one another and press the button
(2g) on the remote control (2). The lights will
flash for as long as the mode is active.
2. Press the button (2g) again in order to de-acti-
vate the mode. The lights will be on constantly
again.

Setting the speed (figure O)

You can set the flight speeds on the remote control
(2) by repeatedly pressing the button (2c). The
basic setting is speed 1 of a total of 3 speeds:
Speed 1 (beeps once)
For first attempts and little flying experience.
Speed 2 (beeps twice)
For pilots with initial flying experience.
Speed 3 (beeps three times)
For very experienced pilots.
PLEASE NOTE: If the remote control is
switched off and on again then the quadro-
copter (1) will be back at speed 1.
360° rollover (figure P)
1. Steer the quadrocopter (1) to a height of
approx. 10m.
2. Keep it hovering and push the button (2d). A
signal tone will sound.
3. Move the joystick (2f) in a flying direction of
the rollover.
4. The quadrocopter (1) will perform a 360°
rollover.
After the rollover the quadrocopter (1) is in nor-
mal flying mode and you can repeat the rollover.
To do this repeat steps 1-4.
Press the button again if you decide not to
perform a rollover but have already pressed the
button.
CAUTION: You need sufficient height in
order to perform a 360° rollover (at least
10m).

Calibration

It is possible that the quadrocopter may fly in an
uncontrolled manner and needs to be calibrated.
Proceed as follows:
1. Switch the quadrocopter (1) on and place it on
a level, horizontal surface.
2. Switch the remote control (2) on and simultane-
ously push the throttle (2e) backwards and to
the left and the joystick (2f) backwards and to
the right. The control lamps (1h) on the quadro-
copter (1) will flash for approx. 3seconds. As
soon as the control lamps (1h) light constantly
the calibration is complete and the quadro-
copter is ready to fly.
PLEASE NOTE: Repeat the calibration if
the quadrocopter still flies in one direction
in an uncontrolled manner.

Recording data (figure U)

You can record images or videos with the camera.
PLEASE NOTE: Remove the protective film
from the lens prior to initial use.
Photo
1. Press once on the OK button (2p).
2. A signal tone will sound and the LED lights (1h)
on the quadrocopter (1) will go off briefly. The
camera (1e) has taken a photo.
Video
1. Hold the OK button (2p) down for approx.
3seconds.
GB/IE 33