Led Displays; Remote Trigger - Bosch FSA 500 Originalbetriebsanleitung

en 24 | FSA ��� | Product description
�.�.� FSA ��� connection panel
DANGER – Risk of electric shock from
excessively high measurement voltage.
The measurement of voltages in excess
of 200 V using Multi measurement leads
CH1 / CH2 will result in injury, heart failure or
fatal electric shocks.
¶
Multi measurement leads CH1 / CH2 are
only to be used for measuring voltages up
to max. 200 V.
¶
Never use Multi measurement leads CH1 /
CH2 to measure mains or similar voltages.
459903-02_Ko
1 2 3 5
4
Fig. 2: FSA 500 connection panel (viewed from underneath)
Connection
Item Color code
Connecting cable B+/B–
1 Red/black
(connecting cable B– for vehicle
ground)
Green/white/ Secondary measuring transduc-
2
yellow er or current probe 30 A or cur-
rent probe 1000 A or adapter cable
1 681 032 098 with fluid pressure
sensor (both special accessories)
3 Green/red/ Multi measurement lead CH2 or
yellow current probe 30 A or current
probe 1000 A
4 Green/blue/ Multi measurement lead CH1 or
yellow current probe 30 A or current
probe 1000 A
5 - Coupling with hose (atmospheric
pressure measurement)
6 -

Remote trigger

White/black Clip-on trigger or adapter cable
7
1 684 465 513 for clip-on sensor
8 Blue/white Oil temperature sensor, air and IR
temperature sensor (special acces-
sories)
9 Yellow/green Connecting cable term. 1/term.
15/EST/TN/TD
10 - Power supply unit connection
11 - - Connection for charging station
(special accessory)
For speed measurements with a clip-on sensor, the adapter
1)
cable 1 684 465 513 must always be connected between the
FSA 500 socket (Pos. 7) and the connecting cables for the
c lip-on sensor.
The color codings on the connection cables refer to the correct
2)
connection at the FSA 500.
|
1 689 989 115 2011-09-20
6 7 8 9 11
10
2)
1)
�.�.4

LED displays

LED A: Status indicator
Status LED A
FSA 500 off.
Not lit
FSA 500 starting.
Red light
Flashing FSA 500 on, but not yet ready for operation.
No data link with PC/Laptop.
white
(1 Hz)
Flashing FSA 500 ready for operation.
green Data link to PC/Laptop established via USB.
(1 Hz)
FSA 500 ready for operation.
Flashing
blue (1 Hz) Data link to PC/Laptop established via Bluetooth.
Flashing Firmware error.
red (4 Hz) FSA 500 not ready for use.
LED B: Charge indicator
Status LED B
Not lit No external power
supply connected.
Power supply via battery.
Violet light External power supply
connected. Battery being
charged.
Blue light External power supply
connected. Battery is
charged.
Red light External power supply
connected.
Possible cause of
trouble:
R Battery temperature
> 45 °C
R Battery not connected
R Battery defective
R Connector defective
�.�.� Remote trigger
The start soft key (F3) or the stop soft key (F4) in the
FSA 500 CompacSoft [plus] software can be activated
with the button on the remote trigger.
2
Fig. 3: Remote trigger (1 684 463 828)
1 Button
2 Connector for FSA 500
i
For connection refer to Fig. 2, Pos. 6.
Action
-
-
External power supply
can be disconnected.
Check battery and
connector.
Allow the FSA 500 to
cool down.
1
459903-04_Ko
Robert Bosch GmbH