Additional Operating Modes And Features - DeVilbiss 9055 Series Betriebshandbuch

A d d i t i o n a l O p e r a t i n g M o d e s a n d F e a t u r e s
time. If you are unable to change the delay time, your provider has locked this setting.
4. If you take your mask off during the night, your bilevel CPAP will automatically stop providing pressure. If the Mask Alert is enabled, an
audible alert will be present for 20 seconds. Pressing any keypad button will cancel this audible alert. Pressing any keypad button a second
time will remove the visible alert from the display. When you put your mask back on and start breathing again, the bilevel CPAP will start
operating. You can use the Delay feature again at this time to get back to sleep.
NOTE—A large system leak will result in a Mask Alert. If the cause of the alert is corrected, the visible and audible alert will cancel and be reset.
5. In the morning, take your mask off and press the ON/OFF button on the keypad to shut the blower OFF. The automatic shutoff feature will
shut the blower OFF if you do not push the ON/OFF button. There will be a 20-second audible alert during the shutdown period if the Mask
Alert is enabled. Pushing any keypad button will cancel this audible alert.

ADDITIONAL OPERATING MODES AND FEATURES

The Display Menu—With the unit ON, press the SELECT button on the keypad to scroll through the items on the display. Not all of these will display
on your unit. Some are optional, depending on what your physician and/or home medical equipment provider has selected. The table below shows
the items you may see and describes the feature associated with each item.
Displayed
Item Text
Examples
Actual Pressure Act Pres
20.0 cmH
Compliance Bar Graph Compl %
70
CPAP Pressure CPAP
20.0 cmH
IPAP Pressure IPAP
20.0 cmH
EPAP Pressure EPAP
10.0 cmH
Delay Time Delay
10 min
Delay Pressure Delay Pr
4.0 cmH
IPAP Rounding IPAP Rnd
1
EPAP Rounding EPAP Rnd
1
Enable Mask Alert Msk Alrt
Enabled
Humidifier Present 9100 Hum
Attached
Compliance Meter ComplHrs
123456.7
Hour Meter Unit Hrs
123456.7
Firmware Version Firmware
M5 V0.17
Serial Number Serial #
95000001
Language Selection Language
English
Description
Actual mask pressure calculated from CPAP
pressure and flow
The bar graph is displayed to give feedback on
device usage. Graph covers usage over the last
30 days of operation (rolling 30-day basis).
Prescription setting – this will be seen only
if your bilevel CPAP is to be used in the
CPAP mode.
Prescription setting – this will be your
inspiration pressure; it is seen if your bilevel
CPAP is to be used in the bilevel mode.
Prescription setting – this will be your
exhalation pressure; it is seen if your bilevel
CPAP is to be used in the bilevel mode.
Selectable delay time setting
Pressure during the delay
IPAP rounding waveform profile
EPAP rounding waveform profile
Indicates whether the 20 second audible
mask alert feature is enabled or disabled.
Indicates that a DeVilbiss humidifier is
connected to the CPAP.
The total number of hours the bilevel CPAP
has sensed breathing.
The total number of hours that the bilevel
CPAP blower has been ON.
Shows version of installed firmware.
Shows the serial number of the bilevel CPAP
unit.
Shows the selected LCD display language.
Range
3-25 cmH O The value displayed may vary slightly from
2
your prescription based on operating
conditions.
0-100% The value displayed is your actual use time
versus the time you are expected to use the
bilevel CPAP.
Delay Pressure to Your provider will set the CPAP prescription
25 cmH O, in 0.5
for your bilevel CPAP.
2
cm increments
EPAP to 25 Your provider will set the IPAP prescription
cmH O, in 0.5 cm
for your bilevel CPAP.
2
increments
Delay pressure to Your provider will set the EPAP prescription
IPAP, in 0.5 cm for your bilevel CPAP.
increments
0 to 45 minutes You can select the delay you desire using the
in 5 minute UP/DOWN button, if the provider has
increments unlocked this setting.
3 cmH O to EPAP Your provider has set the delay pressure
2
(or CPAP in CPAP
value.
mode), in 0.5 cm
increments
0 to 5, in Your provider has set the IPAP rounding
increments of 1 value.
0 to 5, in Your provider has set the EPAP rounding
increments of 1 value.
Enabled or The mask alert can be enabled or disabled by
Disabled using the UP/DOWN button, unless the
provider has locked the alert.
Attached or The indication of the attachment or removal
Removed of the humidifier can be changed using the
UP/DOWN button, unless the provider has
locked this setting.
N/A
N/A
N/A
N/A
Up to 15 The display language can be changed using
selections the UP/DOWN button, unless the provider
has locked the language.
9
Comments
SE-9055