Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Care and cleaning
•
Unplug the Bread Maker and allow to cool completely before cleaning.
•
Before the first use and after every use, clean each part thoroughly.
•
Periodically check all parts before reassembly.
•
Do not use metal tools in the non stick bread pan – always use plastic, nylon or silicone
spatulas etc.
•
Never immerse the unit in water or any other liquid.
•
To clean the unit and control panel, wipe with a clean, damp cloth and dry before storing.
•
Do not use abrasive cleaners, steel wool or abrasive materials or cleansers.
•
Wash the baking pan, kneading paddle, measuring cup and spoon in hot, soapy water, rinse
and dry thoroughly.
•
The baking pan, kneading paddle, measuring cup and spoon are top shelf dishwasher safe.
•
If the kneading paddle is difficult to remove from the bread pan, pour in sufficient warm
soapy water to cover the paddle and leave to soak for 10 – 15 minutes. This will loosen the
paddle.
•
If the kneading paddle still cannot be removed hold the drive shaft from underneath the pan
and twist back and forth until the kneading paddle is released.
•
To clean the baking chamber, remove any bread crumbs by tipping them out or wiping them
away with a slightly damp cloth or clean pastry brush.
•
If food residue burns onto the heating element, allow to cool completely then wipe away
with a damp cloth.
•
Store the Bread Maker with the power cable loosely coiled. Never wrap it tightly around
the bread maker.
38
Electrical connections
THIS APPLIANCE MUST BE EARTHED
This appliance is fitted with a fused three-pin plug to BS1363 which is suitable for use in all
homes fitted with sockets to current specifications. If the fitted plug is not suitable for your socket
outlets, it should be cut off and carefully disposed of. To avoid an electric shock, do not insert the
discarded plug into a socket.
Fitting a new plug
If for any reason you need to fit a new plug, the flexible mains lead must be connected as shown
here. The wires in the mains lead fitted to this appliance are coloured in accordance with the
following code:
Earth(green/yellow)
E
L
Neutral(blue)
10amp fuse
N
Live(brown)
Connect BLUE to Neutral (N)
Connect GREEN & YELLOW to Earth (E)
Connect BROWN to Live (L)
10 amp fuse to be used
If the colours of the wires in the mains lead of this appliance do not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows. The wire which is coloured
green and yellow MUST be connected to the terminal which is marked with the letter E (Earth)
or coloured green. The wire which is coloured blue MUST be connected to the terminal which is
marked with the letter N (Neutral) or coloured black. The wire which is coloured brown MUST be
connected to the terminal which is marked with the letter L (Live) or coloured red.
Before refitting the plug cover, check that there are no cut or stray strands of wire inside the plug.
Use a 10 amp BS1362 fuse. Only BSI or ASTA approved fuses should be used. If you are at all
unsure which plug or fuse to use, always refer to a qualified electrician.
Note: after replacing or changing a fuse on a moulded plug which has a fuse cover, the cover must
be refitted to the plug; the appliance must not be used without a fuse cover. If lost, replacement
fuse covers can be obtained from an electrical shop. This appliance complies with the following
EC Directives: 2006/95/EC (Low Voltage Directive) and 2004/108/EC (EMC Directive).
RECYCLING YOUR ELECTRICALS
Along with many other high street retailers, Lakeland has joined a scheme whereby customers
can take their unwanted electricals to recycling points set up around the country.
Visit www.recycle-more.co.uk to find your nearest recycling point.
39
Werbung
Kapitel
Inhaltsverzeichnis
