Lights; Electrical .Motor; Battery - Flyer C SERIE Anleitung

5.21 Lights

Different lighting systems are installed depend-
ing .on .the .area .of .use .and .bicycle .type. .If .this .is .
done using a daytime running light function, the
system will always switch automatically between
low .beam .and .daytime .running .light.
FLYER with pedal assist over 25 km/h with
high beam
Basic setting: when the system is activated, the
low beam/daytime running light is automatically
switched .on.
Light .button .function: .Switch .between .low .beam/
daytime running light and high beam
FLYER e-mountainbikes
Basic setting: when the system is activated, the
light remains switched off
Light . button . functions: . Activate . the . light . (high .
beam) by pressing the light button; switch to low
beam/daytime running light by pressing the light
button .again. .Switch .off .the .light .by .pressing .and .
holding the light button (at least 1 second)
FLYER with pedal assist up to 25 km/h
Basic setting: when the system is activated, the
light remains switched off
Light . button . functions: . Activate . the . light . (low .
beam/daytime running light) by pressing the light
button; switch off the light by pressing the light
button .again.
Speed sensor
The speed sensor is used to show the speed in
the .FLYER .D1 .display .and .correctly .calculate .the .
assistance .needed.
The speed sensor and the associated spoke magnet
must be fastened so that the distance between the
spoke magnet and the marking position on the speed
sensor .is .1 .to .5 .mm. .If .the .distance .is .different, .an .
error .message .will .appear.
Power supply to external devices
You .can .use .the .USB .port .to .charge .external .de-
vices, .e.g. .smartphones, .that .can .be .powered .via .
USB. . The . charging . cable . of . the . device . can . be .
connected .directly .to .the .FLYER .D1 .display.
In .order .to .charge .external .devices, .your .FLYER .
e-bike .must .contain .a .charged .FLYER .battery.
Open . the . cover . of . the . USB . port . on . the . display .
and .connect .the .charging .cable .to .it.
• Do not place the connected device on
a tilted or unstable place while charg-
ing. . Otherwise, . it . could . fall . and . be-
come .damaged.
• Do not charge external devices in
rainy . weather . or . connect . a . wet . USB .
cable. .The .USB .connection .is .not .wa-
terproof!
• You . must . not . connect . external . de-
vices when riding in the rain and the
USB . p ort . m ust . b e . c ompletely . c overed .
by .the .protective .cap.
• After . using . the . USB . port, . be . sure . to .
firmly .tighten .the .rubber .cap.
• Make .sure .that .the .voltage .of .the .USB .
port . is . suitable . for . your . device. . (For .
voltages, see Technical Data)
5.22 E lectrical motor
Additional . data . and . instructions . concerning . the .
electrical . system . of . your . FLYER . e-bike . are . in-
cluded in the attached operating instructions for
the electrical system installed, which cover the
following components:

• Battery

• Charger
• Drive unit
• Speed sensor and spoke magnet
Information . on . the . function . and . range . of . your .
FLYER's .motor .is .listed .below:
Function
The motor starts working as soon as you start
pedalling when one of the assistance modes has
been .selected.
The performance of the motor depends on sev-
eral factors:
• The .force .used .while .pedalling.
The assistance is more gentle when you
pedal with low force than when you pedal with
higher .force, .e.g. .while .riding .uphill. .However, .
this increases the power consumption and
decreases .the .range.
• The assistance mode
The higher the level of assistance, the more
power .the .motor .will .provide. .However, .
high motor performance means high power
consumption. .The .lowest .assistance .mode .
provides the least assistance but also the
longest .range.
Range
Any . specified . range . information . is . usually . ob-
tained .under .optimal .conditions. .Ranges .achieved .
under .everyday .conditions .will .usually .be .shorter.
Please .consider .this .when .planning .your .route.
The . range . depends . on . many . factors. . These . in-
clude battery capacity, motor assistance level
selected, geographical conditions, road surface,
driving style, environmental temperature, the
weight of the rider, tyre pressure and the technical
state .of .your .FLYER .e-bike.
30