Mixing Fuel - Scheppach Pcs56E Originalbetriebsanleitung

• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the expiry of
the warranty period.
ATTENTION
The device and the packaging are not children's toys!
Do not let children play with plastic bags, films or small
parts! There is a danger of choking or suffocating!
• Remove the quick start guide from the start pull
cord (4).
8.1 Mounting the guide rail and tensioning the
saw chain
m ATTENTION
Always carry out assembly with the engine switched off.
m WARNING
Danger of injury!
Always wear protective gloves when touching the
saw chain (17). Danger of injury due to the sharp cut-
ting teeth!
Note
A new saw chain (17) stretches and needs to be
re-tensioned more often. Check and adjust the chain
tension regularly after each cut.
Depending on wear, the guide rail (16) can be turned.
• Set the chainsaw down on a level and stable surface.
• Pull the front hand guard (1) back as far as it will go
to release the chain brake (see fig. B).
• Remove the two fixing nuts (20) with the spark plug
wrench (31).
• Remove the chain cover (22).
• Slide the slotted hole of the guide rail (16) over the
two protruding pins.
• Place the saw chain (17) over the teeth of the chain
wheel (26). Insert the saw chain (17) accurately in
the direction indicated on the guide rail (16). In the
tip of the guide rail (16) there is a guide wheel into
whose teeth the saw chain (17) must be inserted.
• Pull slightly on the guide rail (16) to slightly pre-ten-
sion the saw chain (17).
• Fit the chain cover (22) back on. Make sure that
the internal chain tensioning pin (23) fits into the
matching hole (25) in the guide rail (16) (see Fig.
S). If necessary, adjust the chain tensioning screw
(21) with the spark plug wrench / slotted screwdriv-
er (31) (see Fig. T).
• Screw on the two fastening nuts (20) by hand. How-
ever, make sure that you do not tighten them yet.
38 | GB
• Use the spark plug wrench / slotted screwdriver (31)
to turn the chain tensioning screw (21) clockwise un-
til the lower part of the saw chain (17) slides into the
guide rail (16). The saw chain (17) must be in contact
with the underside of the bar. When the chain brake
is released, it must be possible to pull the saw chain
(17) over the guide rail (16) by hand (see Fig. U).
Note
A new saw chain (17) stretches and needs to be
re-tensioned more often.
• Tighten the two fixing nuts (20) with the spark plug
wrench / slotted screwdriver (31).

8.2 Mixing fuel

The engine must be operated with a fuel mixture of
petrol and engine oil.
m WARNING
Avoid direct skin contact with fuel and inhalation of
fuel vapours.
Use only a mixture of unleaded petrol (min. RON 95)
and special 2-stroke engine oil (JASO FD/ISO - L -
EGD). Mix the fuel mixture as per the fuel mixing table.
Put the correct amount of petrol and 2-stroke oil into
the enclosed mixing bottle (30) (see "Fuel mixing ta-
ble"). Then shake the mixing container (30) well.
8.2.1 Fuel mixing table
Mixing process: 40 parts petrol to 1 part oil
Petrol ...................................................... 2-stroke oil
0.5 litres ......................................................... 12.5 ml
8.3 Filling with fuel (Fig. R)
m WARNING
Only fill the fuel when the engine is switched off and
has cooled down. There is a risk of fire!
• Always clean the area around the fuel tank cap (13)
before filling to prevent dirt from falling into the fuel
tank. Use a dry, lint-free cloth for this purpose.
• Lay the device on its side with the fuel tank cap (13)
facing upwards.
• Turn the fuel tank cap (13) anti-clockwise and open
it. The fuel tank cap (13) is connected to an anti-loss
device in the fuel tank and thus cannot fall off.
• Pour the fuel mixture into the fuel tank. Do not spill
fuel when refuelling and do not fill the fuel tank to
the brim.
• Wipe up spilled fuel immediately.
• Turn the fuel tank cap (13) clockwise to close it.
NOTE
Also check the chain oil after each fuel fill.
www.scheppach.com