Transport; 11: Storage; Electrical Connection - Scheppach HM100T Originalbetriebsanleitung

DE GB NO PO
Carbon brushes
In the event of excessive spark development, have
the carbon brushes checked by an electrician.
m WARNING!
The carbon brushes must be replaced by an electri-
cian.

10. Transport

Transport (always in table saw mode)
• Move the lower saw blade guard (14) above the saw
guide until you can hear a „click". The front of the
saw blade guard has to be flush with the white line
on the saw guide.
• Position the saw button downwards by pressing the
unlocking button (2) on the saw head and activating
the lock pin (20).
• Put the rip fence (1) on the saw blade guard and
attach it.
• Lift the machine by holding it on both sides of the
lower frame (6).
m WARNING
There is a risk of injury in the event of improper han-
dling of the machine, during lifting or turning.
Always disconnect the mains supply before eve-
ry transport
Only ever transport the saw in table mode and with
the rip fence mounted on the saw blade. This will pre-
vent injury from the saw blade. Never transport the
machine by its safety equipment (e.g. safety guard,
riving knife).
11. Storage
Store the machine and its accessories in a dark, dry
and frost-free place, inaccessible to children. The
ideal storage temperature is between 5 and 30˚C.
Store the power tool in its original packaging.
Cover the power tool to protect it from dust and hu-
midity.
Keep the operating manual with the power tool.

12. Electrical connection

Power supply
The machine can be connected to any power socket
with 230 V AC. Only safety sockets are permitted
which must be protected with a circuit breaker for 16
Amps. Additionally, a residual-current-operated pro-
tective device (RCD) with a maximum of 30 mA must
be connected!
The installed electric motor is connected and op-
erational. The connection complies with relevant
VDE and DIN stipulations. The customer's mains
connection as well as the extension lead used
must comply with these provisions.
• The product complies with EN 61000-3-11 require-
ments and is subject to conditional connection. That
means that connection to randomly selected points is
not permitted.
• Temporary voltage fluctuations can be caused in the
34 І 84
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002-58
GB SE FR DE GB FR DE GB FR
machine in the event of unfavourable mains condi-
tions.
• The product must exclusively be connected to
points which
• a) do not exceed a maximum permitted supply im-
pedance „Z" (Zmax = 0.382 Ω) or
• b) have a continuous current rating of at least 100
A per phase.
• As the user, you have to ensure that, if required in
consultation with your energy supplier, the connec-
tion point from which you would like to operate the
product complies with one of the two specified re-
quirements a) or b).
Important notices
If there is a motor overload, it will turn off automatically.
After a cool-down period (timing varies), the motor can
be turned on again.
Defective electrical connections
Insulation damage often occurs on electrical connec-
tions.
Causes can include:
• Pressure marks when connections are guided
through windows and doors
• Kinks due to inappropriate attachment or guidance
of the connection
• Cuts when the connection is run over
• Insulation damage when being pulled out of the
wall socket
• Tears from ageing insulation
m DANGER
Such defective electrical connections must not be used
and are dangerous to life because of the insulation dam-
age.
Regularly check electrical connections for damage.
Make sure the cable is not connected to the mains when
checking.
Electrical connections must comply with relevant VDE
and DIN stipulations. Only use connections marked
H05VV-F.
Printing the type designation on the connection cable
is the law.
AC motor
• The power voltage has to be 220 – 240 V ~.
• Extension leads up to a length of 25 m must have a
cross section of 1.5 square mm.
Connections and repairs to the electrical equipment
must be carried out by a trained electrician.
If there are any questions, please provide the follow-
ing data:
• Motor's type of power
• Data from the machine's rating plate
• Data from the motor's rating plate
Machine connection
Only ever use machine connection cables which are
not damaged. The machine connection cable must
not exceed 50 m because otherwise the performance
of the electric motor is reduced. The machine con-
nection cable must have a cross section of 3 x 1.5
mm. Machine connection cables are particularly of-
ten subject to insulation damage. Causes include:
• Cuts when the connection is run over;
• Pinching when connections are guided through
windows and doors;
DE GB FR DE GB FR