Scheppach HM100T Originalbetriebsanleitung Seite 32

DE GB NO PO
up to 60° to the right. It can be fixed to defined set-
tings (locks) at 0°, 15°, 22.5°, 30°, 45° and 60°.
In order to turn the rotary table (mitre plate), the lock-
ing button has to be loosened.
WARNING! To prevent the mitre angle from chang-
ing during operation, the locking button (13) has to be
tightened (even when the saw has been fixed in one
of the defined positions).
Rip fence (Fig. 2, 5, 7)
The rip fence (1) is attached to the upper saw table
(4). The lock screw (18) for locking the rip fence must
point to the front of the machine.
The rip fence is attached over the upper saw blade
guard (37).
When attaching the rip fence (1), always ensure that
the guide is secured with the locking button.
When the lock screw (18) has been loosened, the rip
fence (1) can be removed and the switch (3) is acti-
vated.
Use as table saw (Fig. 2, 7)
• The table has to be attached in the correct direction
(Fig. 7), and the lock pin (20) has to be securely
fixed.
• Move the lower saw blade guard (14) above the saw
guide until you can hear a „click". The front of the
saw blade guard has to be flush with the white line
on the saw guide.
• Position the saw button downwards by pressing the
unlocking button (2) on the saw head and activating
the lock pin (20).
• Remove the rip fence (1).
• To turn the machine on and off, use the on/off
switch (3).
After every adjustment, we recommend a test cut
to check the measurements you set.
Use as table saw (Fig. 2, 3, 7, 8)
Set the saw to table mode as described in „Use as
table saw".
On/off switch
• The saw is turned on by pressing the green button
(3). Before starting to saw, wait until the saw blade
(12) has reached its maximum rotational speed.
Press the red button (3) to turn off the saw.
Carrying out longitudinal cuts (Fig. 8, 9)
• Loosen the lock screw (18) and remove the rip
fence.
• Using the measurements on the saw table (4), set
the rip fence (1) to the required position and secure
it with the lock screw (18). Turn on the saw using
the green button (3).
• Slowly and carefully push the work piece along the
rip fence (1) towards the saw blade (12).
• The upper saw blade guard (37) opens automati-
cally when the work piece is pushed forwards.
• WARNING! You must use the push stick (28) in the
area of the saw blade (12) when cutting work piec-
es under 120 mm (see Fig. 9) (included!)
• Always push the work piece through to the end of
the riving knife (38) (Fig. 7).
• After the cut, the safety guard (37) closes automati-
cally and covers the saw blade (12).
• Turn off the saw.
32 І 84
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002-58
GB SE FR DE GB FR DE GB FR
• WARNING! Prevent long work pieces from tipping
at the end of the cutting process (e.g. roller stand.).
Carrying out cross cuts (Fig. 3, 10)
• Insert the cross stop (23) from the front into the side
groove on the saw table (4).
• Loosen the star knob screw (25) and set and fix the
cross stop (23) at the required angle.
• Loosen both star knob screws (24) and push the
fence rail (39) to the left until it no longer touches
the saw blade guard (37) when pushing. Retighten
the screws (24).
• Turn on the saw. Tightly push the work piece to the
fence rail (39) and, together with the cross stop (23)
slowly push it into the saw blade (12) to carry out
the cut.
• When you have finished cutting, turn the saw off.
Use as chop saw
Set the saw to chopping mode as described in „Use
as chop and mitre saw".
Settings (Fig. 2)
• By loosening the lock screw (21), the machine head
can be tilted to the left to a maximum of 45°. By
loosening the locking button (13), the rotary table
(11) can be adjusted from -50° to +60°.
On/off switch (Fig. 2)
• The saw is started by squeezing the on/off switch
(22). You must hold the switch during sawing.
Fine adjustment of the stop for chop cutting at
90° (Fig. 2, 12, 13)
• Stop bracket (b) not included.
• Set the rotary table (11) to the 0° position.
• Lower the machine head by pushing the unlocking
button (2) on the handle (5).
• Loosen the lock screw (21).
• Attach the stop bracket (b) between the saw blade
(12) and the rotary table (11).
• Loosen the counter nut (41) and adjust the set
screw (40) until the angle between the saw blade
(12) and the rotary table (11) is 90°.
• Tighten the counter nut (41) again.
• Then check the position of the angle indicator (42).
If required, loosen the indicator (43) with a crosstip
screw driver, set it to the 0° on the dial (42) and
retighten the lock screw.
Chop cutting at 90° and rotary table at 0°(Fig. 2,
11)
• Turn on the saw by squeezing the on/off switch (22).
• Before starting to saw, wait until the saw blade has
reached its maximum rotational speed.
• Place the work piece on the lower sawing table (11)
and press it onto the fence rail with the left hand.
The material to be cut always has to be held tightly
to the surface so it does not move during cutting.
• Press the unlocking button (2) with the other hand
and move the machine head, using the handle (5),
evenly and with slight pressure downwards through
the work piece. After completing the cutting pro-
cess, return the machine head to the upper rest po-
sition and release the on/off switch (22).
WARNING!
Because of the return spring, the machine automati-
cally springs upwards, i.e. do not let go of the handle
DE GB FR DE GB FR