Scheppach kw 7.0 Originalbetriebsanleitung Seite 24

• When leaving the workplace, switch off the ma-
chine and disconnect the mains plug or switch off
the Cardan shaft drive and the motor and remove
the ignition key.
• All protective and safety equipment must be reas-
sembled immediately after repair or when mainte-
nance is completed.
• The safety, operating and maintenance information of
the manufacturer, as well as the dimensions specified
in the technical data, must be observed.
• The relevant accident prevention regulations and
the other generally accepted safety rules must be
observed.
• Make sure that you have secure footing and always
maintain your balance.
• Check the product for potential damage!
• All components and protective devices must be
carefully inspected to ensure that they are fault-free
and function as intended prior to continued use of
the machine.
• Check whether the moving parts function faultlessly
and do not jam or whether parts are damaged. All
parts must be correctly mounted and all conditions
must be fulfilled to ensure fault-free operation of
the product.
• Damaged protective devices and parts must be
repaired properly or replaced by a recognised spe-
cialist workshop unless otherwise specified in the
operating instructions.
• This product conforms to the applicable safety
regulations. Repairs may only be performed by
a specialist using original spare parts. Otherwise
accidents could occur.
• Wear suitable personal protective equipment. This
includes:
- Hearing protection to prevent the risk of devel-
oping hearing loss
- Respiratory protection to avoid the risk of inhal-
ing damaging dust
- Wear gloves when handling saw blades and
rough materials. Saw blades must be carried in
a container whenever practical.
• The operator must be informed about the conditions
that affect the noise levels (e.g. saw blades designed
to reduce noise, care of saw blade and machine).
• Faults in the machine, including the guards and the
saw blade, must be reported to the person respon-
sible for safety as soon as they are discovered.
• When transporting the machine, use only the trans-
port devices and never use the guards for handling
and transport.
• All operators must be adequately trained in the use,
setting and operation of the machine.
• Do not saw any material to be cut that contain for-
eign bodies such as wires, cables or cords.
• Only use sharp saw blades.
24 | GB
• Arrange the workpiece stack to be processed and
the finished workpieces close to the normal work-
place of the operator.
• Only use original, undamaged flanges as specified
by the manufacturer and those that are suitable for
the purpose.
• The machine must be on a horizontal, level floor
during operation and the floor around the machine
must be level, well maintained and free of waste
such as chips and cut-off workpieces.
• Do not use the machine at locations with a high risk
of fire.
Warning! This product generates an electromagnetic
field during operation. This field can impair active or
passive medical implants under certain circumstanc-
es. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the man-
ufacturer of the medical implant prior to operating
the product.
Residual risks
The machine has been built according to the
state-of-the-art and the recognised technical
safety requirements. However, individual resid-
ual risks can arise during operation.
• Danger of injury for fingers and hands due to the
rotating saw blade with improper guiding of the
workpiece.
• Risk to health from wood dust or wood chippings.
The type of wood and degree of drying has an influ-
ence on the exposure to dust. Use a chip extraction
system if necessary.
• Wearing personal protective equipment such as
protective goggles and dust masks is mandatory.
• Risk to health due to noise. The permissible noise
level is exceeded during operations. It is essential
that personal protective equipment, such as hear-
ing protection, is worn.
• Hazard due to electrical power, with the use of
improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still
remain.
• Residual risks can be minimised if the "Safety
Instructions" and the "Intended Use" together with
the operating manual as a whole are observed.
• Injuries due to defective saw blade. Check the
integrity of the saw blade regularly and before each
use.
• When using special accessories, the operating
instructions enclosed with the special accessories
must be observed and read carefully.
• The noise emission can be reduced by using a spe-
cific saw blade.
www.scheppach.com