Herunterladen Diese Seite drucken

Ego Power+ RM2000E Übersetzung Der Originalanleitung Seite 15

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 24
10.5.4 Systematic cutting mode
When in Systematic cutting mode the product will mow in parallel
patterns.
1.
Do steps 1-3 in 10.1 To get access to the main menu .
2.
Tap
to enter the 2
page of the cutting mode setting.
nd
3.
Tap
to enter SYSTEMATIC-CUT mode.
4.
Activate the cutting mode, and tap
10.6 Boundary Setting
10.6.1 Drive past wire
This is the distance that the front of the product can move past the
boundary wire. The factory setting is 30 cm. You can select a distance
of 20-55 cm.
1.
Do steps 1-3 in 10.1 To get access to the main menu .
2.
Tap
to enter BOUNDARY setting.
3.
Tap
to enter DRIVE PAST WIRE setting.
4.
Tap
or
to select the distance and tap
10.6.2 Exit station
The product will back along the wire to the set distance and then depart
to mow. You can set a distance of 20-999 cm. The factory setting is
20 cm.
1.
Do steps 1-2 in 10.6.1 Drive past wire .
2.
Tap
to enter SMART EXIT CHARGING STATION setting.
3.
Enter the distance and tap
10.7 Security Setting
You must enter the PIN code to access the security setting.
Do steps 1-3 in 10.1 To get access to the main menu .
1.
2.
Tap
to enter the PIN code and tap
the 1
page of the security setting, tap
st
PIN code
You can change the PIN code.
1.
On the 1
page of the security setting tap
st
PIN code. Then tap
to confirm.
2.
Enter the PIN code again to verify, tap
Alarm setting
This function means that an alarm will sound if the product occurs
some fault messages. You can set the alarm duration of 1-10 minutes.
The default duration of alarm is 2 minutes.
You can activate or deactivate the ALARM SETTING .
You can activate or deactivate the Alarm When Lift only when the ALRM
SETTING is activated.
To activate the alarm setting
1.
On the 1
page tap
to enter ALARM SETTING .
st
2.
Activate the ALARM SETTING . Tap
of alarm.
to confirm.
to confirm.
to confirm.
to confirm. Then enter
to enter the 2
page.
nd
to change the
to confirm.
or
to select the duration
3.
Activate or deactivate the Alarm When Lift .
4.
Tap
to confirm.
Geofence setting
The geofence is the circle formed with the charging station as center
point and the radius from the center point to the current position.
You can set sensitivity level of low (500 m), medium (250 m) and high
(100 m). The higher level of Geofence sensitivity, the easier the alarm
starts.
1.
On the 2
page tap
to enter GEOFENCE SETTING .
nd
2.
Activate the geofence setting.
3.
Tap the sensitivity level and tap
10.8 Messages
In this menu the previous fault and information messages can be found.
10.8.1 Fault message
Messages shown in the display are the actual fault. The newer alarms
are listed at the top. To the fault messages there are tips and advice to
help to rectify the fault. Refer to FAULT MESSAGES LIST in this manual.
1.
Do steps 1-3 in 10.1 To get access to the main menu .
2.
Tap
to enter MESSAGES .
3.
Tap
to display FAULT MESSAGES . Tap
other fault messages.
4.
Tap the selected fault message to display the fault detail.
10.8.2 Information message
Messages shown in the display not caused by an actual fault
are instead saved under the Info messages heading. For more
information concerning the possible caused of each message, refer to
INFORMATION MESSAGES LIST in this manual.
1.
Do steps 1-2 in 10.8.1 Fault information to enter the message
menu .
2.
Tap
to display INFORMATION MESSAGES . Tap
scan the other information messages.
3.
Tap the selected information message to display the information
detail.
10.9 Others setting
10.9.1 Rain sensor setting
When rain is detected, the robot returns to the charging station and
restarts until the rain sensor is dry and delay time is over. You can set
the delay time of 0-240 minutes. The default delay time is 180 minutes.
1.
Do steps 1-3 in 10.1 To get access to the main menu .
2.
Tap
to enter the 1
page of the others setting, tap
st
enter the 2
page.
nd
3.
Tap
to enter RAIN SENSOR SETTING .
4.
Activate the rain sensor setting. Set the delay time and tap
to confirm.
ROBOTIC MOWER — RM4000E
EN
to confirm.
or
to scan the
or
to
to
15

Werbung

loading

Verwandte Produkte für Ego Power+ RM2000E