Teac R-919X Bedienungsanleitung Seite 9

_ CDS (Computomatic Direct
Selection) Function.
The CDS system allows direct access to any
recorded tune by presetting the tune number
counted from the beginning of the tape.
(R-919X only: Before starting CDS search,
set the REVERSE MODE button toc posi-
tion.) The tune number can be preset by
pressing the <4 ( <4 or P® on R-919X)
button first and then the CDS/CPS button.
"PL 1" will appear in the Multi Counter
when the CDS/CPS button is pressed
first, then the PL number will increase by
one each time the CDS/CPS button is
pressed. Thus "PL 5" will appear if the
button is pressed 5 times. In the CDS
system, as the CDS searching is always
started from the beginning of SIDE A or
SIDE B (R-919X only), first you must know
the side on which the tune to be searched
has been recorded.
To exit from the CDS mode,
¢ Push the COUNTER CLEAR button
while the tape is being rewound.
¢ Push the ¢4 or >> button if the tape
is being forwarded for searching.
Note:
eWhen the tape has already been rewound
to its beginning, use the CPS function
to locate the desired tune instead of the
CDS function.
GPS (Computomatic range
Search) Function"
CPS allows playback up to 15 tunes ahead
or before the one being played. This func-
tion is performed by detecting blank spaces
of at least 4 seconds between tunes. Blanks
can be created using the REC MUTE facility.
1. Press the CDS/CPS button repeatedly
or hold it until the number of tunes to
be skipped appears in the multi func-
tion counter. Refer to the chart "How to
Select a Desired Tune Using CPS".
elf the displayed number exceeds the re-
quired one, keep pressing the CDS/CPS
button as 1 appears after tune number
15 is indicated.
2. Press ¢4 or pe button, depending on
the search direction.
3. As the tape is fast-wound and blank
spaces between tunes are detected, the
displayed number will decrease until it
reaches "1", at which point playback
will start.
(R-919X)
CPS tape side is determined by the setting
of the REVERSE MODE button. See chart
"CPS Tape Side Decided by REVERSE
MODE button".
Notes:
eCPS setting is possible in any tape op-
eration mode.
To cancel the CPS function before pres-
sing 4 of p> button, press the COUNT-
ER CLEAR, COUNTER MODE, STOP, >
(and 4 on R-919X) and PAUSE button.
eSee also: "Notes Common to INTRO
CHECK, CDS, CPS".
Notes Common to INTRO CHECK,
CDS, CPS
Various search functions — INTRO CHECK,
CDS, CPS — are performed by detecting
and counting blanks of about 4 seconds,
such as intervals between tunes.
Therefore, with the following types of
tapes, search functions may not work
correctly.
eWhen the intervals between tunes cannot
be detected.
— Intervals of less than 4 seconds.
— High levels of noise in intervals (due
to recording old scratched records,
poor FM or AM reception, etc.).
eWhen parts of the program are likely to
be detected as intervals between tunes:
— Long low level sections in classical
music, etc.
— Momentary pauses in a speech at a
conference, etc.
— Continuing low level portions created
by fading out, etc.
ein the case of tapes containing fade-outs,
because the length of the blanks can differ
depending on how the fade-out was
performed, some tune intervals may be
detected and others may not.
This problem can be corrected using the
REC MUTE facility.
This correction is particularly necessary
when making recordings using the dbx NR
system.
Tape Memory Functions
Memory Start Playback
1. Press the START M button at the
desired point on the tape during play,
play-pause, record, record-pause or re-
cord-mute.
2. Press the #4 button after playback or re-
cording. When the memorized position is
reached, the deck will automatically
start playback.
Memory Stop
1, Press the STOP M button at the desired
position on the tape during play, play-
pause, record, record-pause or record-
mute.
2. Press the 4 button after playback or
recording. When the memorized posi-
tion is reached, the tape will stop auto-
matically.
Notes:
e Tape transport may not always start or
stop exactly at the memorized counter
index due to the force of inertia from
fast winding.
How to Select a Desired Tune Using CPS
Ex: See (1). To select the 3rd tune past the current tape position, select "3".
(1) Current tape position (2)
g 8 al ao 8
a) H j {
op 4 3 3 Direct f
{i Ges fel fol (=) tbe?
—8 g ate
In example (1), if "t" is less than AN€2d | Before
4 seconds, it will not be counted j
as a blank space. Designate
"2" instead of 3" to select
the 3rd tune in this case.
(3) Current tape position (4)
@ og @g @ @ @
Direction of
tape travel
lb nnn mE
eS
Ahead : Before
CPS Tape Side Decided by REVERSE MODE Button (R-919X)
Reverse
Mode
CPS Tape Side
casi x) CE
Cc Side A only | Side A Side B Side A 2 Side B
>> =
| <] Side B only Side B > Side A Side B 2 Side A
Cc Side A only Side A only Side A = Side B
<4
<j Side B only Side B only Side B 2 Side A