Set The Timer - Teac R-919X Bedienungsanleitung

the CPS and INTRO CHECK functions;
they have priority.
CAN Facility (R-919X)
This facility is provided so that the deck
will skip long blank portions during play-
back for greater efficiency.
1. During playback, press the BLANK
SCAN button (its indicator will light) .
2. If a blank section of more than about 10
seconds is detected during playback, the
deck will automatically fast forward the
tape to the beginning of the next re-
corded section from which point play-
back will resume.
3. To release this function, press the
BLANK SCAN button again (its indi-
cator will go off).
4. If the STOP button is not pressed, the
point at which the deck stops is deter-
mined by the setting of the REVERSE
MODE switch.
<=: Stops when the end of the tape
is reached.
=>: Stops when the end of the reverse
side is reached.
Cc: As long as there is a recorded
section before the end of the
second side, blank scan is con-
tinuous; otherwise it automatical-
ly stops after completing a full
loop of tape after the initial side.
Note:
elf a tape portion at a particularly low level
is continued for more than 10 seconds,
such as a pianissimo section in classica
music, etc., it may be detected as a blank
and the Blank Scan operation may not
work correctly.
In the middle of a tape
2. Make all the preparations as for normal
recording, but leave the deck in the stop
made.
3. Set the audio timer to the required start
(power on) and stop (power off) times.
4. Set the TIMER switch on the deck to
REC.
When the preset start time is reached,
power will be supplied and recording will
start.
(R-919X)
Note: The tape direction (or ») does not
change when the power is cut. Take this
into account for timer-controlled operation.
Timer-Controlled Playback Operation
1. Check that the deck is correctly con-
nected to the amplifier for normal play-
back operation.
2. Connect the deck and amplifier to a
audio timer as for timer-controlled re-
cording (left).
{R-919X)
Determine the side of tape you want to play
first.
3. Make all preparation as for normal play-
back, but do not set the tape in motion.
4. Set the audio timer to the required start
(power on) and stop (power off) times.
5. Set the TIMER switch on the deck to
PLAY.
When the preset start time is reached,
power will be switched on and play-
back will start.
Remote Controlled Operation
(Fig. 7)
The provided RC-311 remote control unit
allows the R-919X/V-970X to be operated
from a distance. The control buttons on the
Fast-forward Play remote control unit function in almost the
same way as those on the front panel of the
a R-919X/V-970X, but they have slightly
fix. different names, etc. For differences, refer
to the table below.
Play
Blank ple > ~
fa Seeds | Comparison between buttons on the remote
| control unit and on the front panel
At the end of either side | Buttons on the remote Buttons on the front
[control unit panel
Tape end SIDE B Play RC-311 R-919X/V-970X
AUTO MONITOR | AUTO MONITOR
INTRO CHECK INTRO CHECK
START MEMO |__STARTM
|_ STOP MEMO |_STOPM
Play CLEAR CLEAR
Fast-forward k pl Lo
BOP Ye "RECORD > *1 | RECORD
REC MUTE PAUSE/REC MUTE
PAUSE PAUSE/REC MUTE
"« "«
CPS CPS/CDS
»> »
Timer-Controlled Recording Operation PLAY 4 *2 <
PLAY > >
1, Connect your deck and stereo system to
a commercially available clock timer as
shown in the diagram.
(R-919X)
Determine the side of tape on which you
want start recording with the ¢ or > button.
*1— Press two buttons simultaneously. The button
does not function with the V-970X.
*2 This button does not function with the V-970X.
=H
Precautions on Remote Control
Operation (Fig. 8 and 9)
1. Battery Placement
1. Remove the lid.
2. Insert 2 "AA" type dry cell batteries.
Be sure that batteries are inserted with
the negative and positive terminals cor-
rectly positioned.
3. Close the unit until it snaps.
How often should the batteries be changed?
The batteries will normally last about six
months. However if you notice that a
shorter distance between the remote contro!
unit and the R-919X/V-970X is required for
Operation, the batteries should be changed.
Replace the batteries with two new ones.
Precautions regarding batteries
eBe sure to insert the batteries with the
positive (+) and negative (-) terminals
correctly positioned.
e Replace the batteries with the same type.
Never try to use a different type of
battery.
eRechargeable and non-rechargeable bat-
teries can be used. Refer to their pre-
caution labels.
Remove the batteries from the remote
control unit when it will not going to be
used for a long period of time.
Replace weak batteries as soon as possible.
¢Do not heat, take apart, or dispose of the
batteries in a fire.
2. Remote Control Unit RC-311
When operating the remote control, point
the front of the unit at the REMOTE
SENSOR on the R-919X/V-970X. The re-
mote control unit may be used within the
range shown in the figure.
Notes:
e Even if the remote control unit is operated
within the effective range, remote control
operation may be impossible if there is
any obstruction between the R-919X/
V-970X and the remote control unit.
elf the deck is operated in the vicinity of
other appliances generating infrared rays,
or if other remote contro! devices using
infrared rays are used near the R-919X/
V-970X, the deck may operate impro-
perly. Conversely, if the R-919X/V-970X's
remote control unit is operated in the
vicinity of other appliances which use an
infrared remote control device, the
other appliance may operate impro-
perly.
eWhen the unit will not be used for a
long period of time (more than one
month), remove the batteries to prevent
them from leaking. If leakage should take
place, wipe up the liquid inside the com-
partment and replace the batteries with
new ones.
Do not place books or other objects on
the remote control unit since they might
depress the buttons and run down the
batteries.