Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installation and operating manual
–
Rope, products in contact with the rope and rigging must not
be soiled by heavily soiling building materials such as conc-
rete, epoxy resin or other adhesive materials. Protect the
products against soiling! Always use brush attachments to
clean the wire rope in an extremely dirty environment.
–
If sand-blasting or painting work is carried out in the vicinity
of the hoist, cover the hoists so that the effectiveness of the
brake is not impaired.
–
Abide by the rope's withdrawal criteria, see '15.4 Care and
maintenance, Rope' on page 20.
–
Clean regularly.
–
Check that all of the screw connections are tight.
–
Replace any damaged parts or have them repaired by a
specialist. Repairs are only to be carried out by a specialist
workshop or by personnel from TRACTEL Greifzug GmbH.
–
Never use a high pressure cleaner to clean the rope or
products in contact with the rope! Penetrating moisture will
result in malfunctions and damage to mechanical installati-
ons (e.g. brakes, ball bearings) and the electrical equipment.
–
Dirt on the wire rope will result in premature wear or the
corrosion of the wire rope, rigging and products in contact
with the rope.
–
Do not lubricate the rope using a lubricant that contains
disulfide (e.g. Molycote
).
®
–
You must abide by the safety specification sheets issued by
the manufacturer of the lubricant being used.
–
Abide by the instructions concerning transport, storage and
cleaning listed on page 18.
–
The anchoring devices must comply with the instructions
given in this manual or the applicable directives / standards.
–
The permitted working load must never be exceeded.
–
Motors can become hot whilst working. Never touch the
motors.
–
Operation without plugs on the motor (Position 3, see Fig.
14) is prohibited. Moisture can impair the effectiveness of
the brake. Risk of injury on the exposed motor shaft.
–
Working outdoors during lightning or a storm is prohibited.
Danger of lightning strikes or the load being tipped over by
gusts of wind.
–
Local climate and weather conditions must always be taken
into consideration during the planning stages: If in doubt,
you must request the weather and wind forecast from the
meteorological office before beginning work.
–
Maintenance and repair work must only be undertaken by
authorized service personnel, see '15.1 Authorized mainte-
nance personnel' on page 19.
–
Self-locking nuts must never be reused and they must al-
ways be exchanged for new ones.
–
Only qualified personnel who have been trained on the
system are permitted to install and operate it in compliance
with the instructions given in this instruction manual.
–
Private users are obliged to obtain training in the assembly,
operation and maintenance of the unit by TRACTEL
Greifzug GmbH.
EN-4
–
Only qualified electricians or trainees supervised by a quali-
fied electrician are permitted to undertake work on the elec-
trical equipment in accordance with the electro technical
standards, rules and regulations.
–
The electric connection must be implemented as described
in '9.3 Assembly, Electrical connection' on page 12 in order
to avoid electrical hazards.
–
Never stand beneath suspended loads. Cordon off the
dangerous area whenever necessary. Support and secure
caught or jammed loads.
–
Never grasp the wire rope while the machine is operating.
–
Never reach into the inlet or outlet of rope contacting devi-
ces whilst the machine is operating. There is a risk of being
pulled in and crushed.
–
Hearing protection may be necessary, depending on how
the hoist is installed.
–
If the load cannot be guided by on-site means then a rota-
tion-resistant wire rope with a swivel hook or a rope swivel
must be used. Swivel hook and rope swivel must turn freely
when subjected to loads.
–
When performing welding work the national safety and
accident prevention regulations must be observed (e.g.
BGR 159 in Germany).
2.2
Instructions for the operator
–
The operating company is responsible for the creation of an
emergency rescue plan and for the provision of information
concerning this to all equipment operators / supervisors.
The emergency rescue plan must be specified in writing and
kept together with this operation manual.
–
The operating company is responsible for training personnel
in all of the measures set out in the emergency rescue plan
under safe conditions.
–
If more than one person is entrusted with the tasks men-
tioned above then the operator must appoint a supervisor
who is authorized to issue instructions.
–
The operator is also responsible for preparing clear operat-
ing, maintenance, repair and other working instructions and
ensuring that the unit is operated correctly by instructing and
training the personnel in the correct and approved utilization
methods.
–
Attached warning signs and information signs must be
readable at all times. Missing or illegible warning signs and
information signs must be replaced immediately.
–
The operator is responsible for the correct operation of the
system as well as for adhering to the maintenance periods
and the undertaking of the service work.
–
A minimum weight is always required for an emergency
descent.
–
The operator or the system manufacturer must ensure that
the payload can be traversed against the static friction in a
manual emergency descent in any situation (e.g. if the rope
is reeved) and that the maximum working load is not excee-
ded.
G919.6 - 07/2012
Werbung
