Werbung
Verfügbare Sprachen
Verfügbare Sprachen
FRONT РАМЫ.
ҮАМАНА
DIGITAL REVERBERATOR
REV7
MEMORY
POWER
MONO
INPUT
ЕС
—0—
—
MD —
—— H
X STEREO
NP
= ОНИ OFF
mz `
LEVEL
FREQ
LEVEL
FREQ
LEVEL
1.
ов sdy 2
IAE
asl,
10
100
`
Ly
t] d
m
X OE
x2c 20: ©
XU:
-
`
-
ч
=
ч
a
`
=
IT
FUN
rN
ETN
N
ы
Too
-5
+5
635
5
-5
+15
2
20
@ POWER ON/OFF switch
When the power is turned on, the last program and parameter
selected will appear on the LCD.
Ө MONO/STEREO
switch
The REV7's reverb signal is always output in stereo, whether
the
input signal
is stereo
or
mono,
If a mono
signal is
received
at the Left input only, this switch, when set to
MONO,
sends the direct signal out of both outputs. With a
stereo input, this switch should be turned off. When switched
to MONO
the MONO
LED is illuminated. (See the BLOCK
DIAGRAM)
© INPUT LEVEL control
Varies the level of the input signal, over a range of +10 dB to
—90 dB. At position "8" gives nominal gain of +4 dB.
© EQ ON/OFF switch `
Allows you to switch the parametric EQ section ON or OFF,
for instant comparison of equalized signal and original signal.
When turned ON the EQ ON LED is illuminated.
© EQUALIZER section
A three-band
semi-parametric equalizer that allows you to
equalize the input signal prior to being processed
into a
digital reverb signal. The direct signal is NOT affected.
Each of the three bands has a frequency control and a level
control (+/—15 dB): The frequency ranges are as follows:
LO: 50Hz — 700Hz
MID: 0.35kHz — 5kHz
НІ: 2kHz ^ 20kHz
^ EI
TT
+5 | АШ
ab
TES д
AIT Ц
LANTA
РАЙ
TTT
ғаны ES
SSC K LALI del
HH
+10
Li/| IS
D TIT
АТ
УХУ
РАНЕЕ ШІ
ишш
ӨЛЕР? (іу, чигин!
TI
ИА ҸМ T TII
CCE
CE
ILE
T LA
LL lS
LEES XC IND
Lat
"UO
IN
У
EN
ВАРНА У НИТ
ZN ЛПУ ТШЩ
САКАЛ
МУ КУТ
ЧЕ
ЧУ МУ
te EE
15 [I U PET
LEITEN
TB
lll
|
FREQUENCY (Hz)
š
RESPONSE
(dB)
-
о
MIXING
`
} d
@-
FA
-15
315
DIRECT REV
@ MIXING control
Allows you to balance the reverb signal with the direct signal.
When turned completely to the left, only the direct signal is
heard. When turned completely to the right, only the reverb
signal is heard.
€) DIRECT RECALL keys
These
keys allow rapid and direct recall of the 30 preset
programs and the first 7 user programs, as explained in the
DIRECT RECALL section.
Q PARAMETER SELECT and +/—keys
Allows
selection
of
up
to
7 programmable
parameters
relating to each
of the preset programs,
for editing and
creation
of new
programs.
Pressing the +/— keys raises or
lowers
parameter
values
and
other
values
(MIDI
channel
number,
program
number,
etc.) by 1; holding down
these
keys permits continuous increase or decrease.
© NUMERIC/EDITING keys
For numerically
entering
program
numbers or parameter
values.
includes
numbers
0 to 9 and decimal
point. The
CLEAR
key zeros the display. The ENTER
key enters the
new
value, when
using the numeric keys for editing para-
meters.
@ OUTPUT CONTROL keys
The MUTE key cancels the entire output. The OUT PHASE
key reverses the polarity of the right output of the reverb
signal. The BYPASS
key cancels the reverb signal only, for
immediate
comparison
of direct
signal/direct
signal
plus
reverb.
|
(D MIDI CTRL key
Pressing
this Key puts the REV7
into the MIDI
Control
Mode, allowing you to set the MIDI Channel on which MIDI
signals are
received,
and
then
program
in pairs of voice
numbers and effects numbers so that effects may be automa-
tically selected from a MIDI instrument, by pressing its Voice
Select keys. Note that this key must be turned OFF before
selection of programs can occur.
|
Werbung
