Programming Tracks; Play Mode - Ricatech Rmc240 Anleitung

ESPAÑOL
LOCALIZADORES DE CONTROLES
PLACA DE ESCALA DE DIAL
SENSOR
INTERRUPTOR DE
ACTIVACIÓN-DESACTIVACIÓN
/ CONTROL DE VOLUMEN
INTERRUPTOR DE
RADIO/CD/AUDIO
SALTO HACIA DELANTE
INTERRUPTOR DE
AM/FM/FM.ST
SALTO HACIA ATRÁS
TOMA PARA AURICULARES
GRABAR/BORRAR
BANDEJA DE CD
TARJETA SD PUERTO USB
DETENER/SD/USB
REPRODUCCIÓN/PAUSAR
SD/USB
SALTO HACIA ATRÁS
0-9
REC/
GRABAR/BORRAR
ERASE
ALTAVOCES
PANTALLA LCD
INDICADOR DE ENCENDIDO
EXPULSAR CASETE/ PLETINA DEL CASETE
AVANCE RÁPIDO
ABRIR/CERRAR
SALTO HACIA DELANTE
PROG/REPETIR
47
ENGLISH
USB Specification
Interface:
- USB 2.0 Full speed, HOST (USB HUB is not supported) Corresponding Flash memory
- Compatible with MPEG Audio 1, 2, 2.5
- Compatible with Layer 1, 2, 3
- Compatible with Bit rate: 128 – 320 Kbps
- Subfolder nest : 8 levels
- Number of track / titles max 999
- Support ID3 tag V2.0

PROGRAMMING TRACKS

P E R I L L A D E
Up to 20 tracks can be programmed to play tracks on an Audio or MP3-CD, USB Device or SD Card in the desired
SINTONIZACIÓN
sequence.
LED FM.ST
1. In " STOP " position, press PROGRAM /
DETENER/SD/USB
REPRODUCCIÓN/
P
CD
PAUSAR
ABRIR/CERRAR
2. Press the FORWARD SKIP /
number appears on the display.
PROG/REPETIR
3. For MP3 Programming: press and hold the PLAY/PAUSE key /
4. Press PROGRAM /
P CD
5. Repeat steps 2-3 to select and store all desired tracks. " FULL " is displayed if you attempt to program more
than 20 tracks.
P CD
6. Press PLAY/PAUSE /
Erasing the Program – by Remote Control or on the Main Unit
You can erase the contents of the memory as follows:
- In Stop position: Press " STOP " once, or
- During Playback: Press " STOP " twice, or
- Turn the ON-OFF Switch/Volume Control to OFF, or
- Select another sound source/function, or
- Press the CD OPEN/CLOSE button to open the CD door.(at CD mode)

PLAY MODE

Repeat Play Mode for CD-DA or MP3 Playback
1. Press REPEAT /
2. The default Play Mode function is OFF.
3. For CD-DA playback there is a choice of 2 Play Modes: "REPEAT 1" / "REPEAT ALL"
4. For MP3 Playback there is a choice of 3 Play Modes: "REPEAT 1" / "REPEAT FOLDER" / "REPEAT ALL".
MP3 RECORDING
Recording from CD to USB / SD
The system is capable of converting (encoding) a whole Audio CD into MP3 format and copy/record this to a USB
mass storage device (e.g. a Flash Drive) or SD card (not supplied). It can also copy a single MP3 track to/from
a USB device or SD card.
1. In CD playback mode, press REC /
devices are detected), playback will stop and skip back to the beginning of the current track, the system
will scan the contents of the USB/SD Card and create a folder to store the MP3 Tracks in. Resume CD playback
and ripping will start from that moment. " USB " or " CARD " will start flashing, depending on the device selected.
2. Press STOP /
MP3 CD/USB/SD Copying
1. In MP3-CD, USB or SD Card playback mode, press REC /
or SD card, USB to SD Card and SD Card to USB. Playback will stop and the system will scan the contents
of the USB or SD card and create a folder to store the MP3 tracks in.
2. " REC " will show on the display.
3. " COPY " will be displayed.
4. Either "USB" or "CARD" will start flashing, MP3 copying starts, the process will stop when copying has finished.
5. The current MP3 track will play back from the beginning.
to start programming - "P" and P0-01 will start flashing on the display.
or BACKWARD SKIP / buttons once or repeatedly until the desired track
to confirm, the display shows the stored track number and the next store position.
to play the programmed tracks.
on the Remote Control while in Play mode.
to start ripping (recording) to USB/SD card (the default is USB if both
to exit CD ripping.
to start MP3 copying from MP3-CD to USB
8
to select the desired album.