Siemens simovert masterdrives Betriebsanleitung Seite 327

04.2006
Parameter assignments depending on setpoint source (P368) and control type (P100):
Parameter description
P554.1 Src ON/OFF1
P555.1 Src OFF2
P561.1 Src InvRelease
P565.1 Src1 Fault Reset
P567.1 Src3 Fault Reset
P568.1 Src Jog Bit0
P571.1 Src FWD Speed
P572.1 Src REV Speed
P573.1 Src MOP Up
P574.1 Src MOP Down
P580.1 Src FixSetp Bit0
P581.1 Src FixSetp Bit1
P590 Src BICO DSet
P651.1 Src DigOut1
P652.1 Src DigOut2
P653.1 Src DigOut3
P654.1 Src DigOut4
Setpoint conn. parameter
Siemens AG 6SE7087-6KD60
SIMOVERT MASTERDRIVES
P368 = 0 P368 = 1 P368 = 2
PMU + Analog FSetp +
MOP inp. + terminals
terminals
B0005 B0022 B0022
1 B0020 B0020
1 B0016
B2107 B2107 B2107
0 B0018 B0018
0 0
1 1
1 1
B0008 0
B0009 0
0 0 B0014
0 0 B0016
*
B0014 0
*
B0107 B0107 B0107
*
B0104 B0104 B0104
0 * B0115
0 0
KK0058 K0011 KK0040
* For factory setting P366 = 2, 3
♦ P590 = B0012
♦ P651 = B0000
♦ P652 = B0000
♦ P653 = B0107
** For factory setting P366 = 4:
♦ P590 = B4102
Bxxxx = Binector (Digital signal; values 0 and 1)
Kxxxx = Connector (16-bit signal; 4000h = 100 %)
KKxxxx = Double connector (32-bit signal; 4000 0000h = 100 %)
v/f characteristic + n/f-control:
T-control + n/f control:
Operating Instructions
P368 = Setpoint source
P368 = 3 P368 = 4
MOP + USS
terminals
B0022 B2100
B0020 B2101
1 1 1
B2107 B2107
B0018 0
0 0 B2108
1 1 B2111
1 1 B2112
0 B0014 0
0 B0016 0
0 0
0 0
0 0 0
B0107 B0107
B0104 B0104
0 0 0
0 0 0
KK0058 K2002
Setpoint connector parameter
(Setp-KP) = P443
Setpoint connector parameter
(Setp-KP) = P486
Parameterizing Steps
P368 = 6 P368 = 7 P368 = 8
PROFI- OP1S + OP1S +
BUS FSetp MOP
B3100 B2100 B2100
B3101 1 1
1 1 1
B2107 B2107 B2107
0 0 0
B3108 B2108 0
B3111 B2111 1
B3112 B2112 B2112
0 0 B2113
0 0 B2114
0 0 0
0 0 0
*
B0014 B0014 B0014
*
B0107 B0107 B0107
*
B0104 B0104 B0104
*
0 0 0
0 0 0
K3002 KK0040 KK0058
9-37
**
*
*
*