Siemens simovert masterdrives Betriebsanleitung Seite 296

Parameterizing Steps
Factory settings
dependent on P366
Para- Designation of the
meters parameter on the
depen- OP1S
dent on
P366
(Src = Source)
P443 Src MainSetpoint
P554 Src ON/OFF1
P555 Src1 OFF2
P556 Src2 OFF2
P565 Src1 Fault Reset
P566 Src2 Fault Reset
P567 Src3 Fault Reset
P568 Src Jog Bit0
P571 Src FWD Speed
P572 Src REV Speed
P573 Src MOP UP
P574 Src MOP Down
P575 Src No ExtFault1
P588 Src No Ext Warn1
P590 Src BICO DSet
P651 Src DigOut1
P652 Src DigOut2
P653 Src DigOut3
P693.1 SCI AnaOutActV 1
P693.2 SCI AnaOutActV 2
P693.3 SCI AnaOutActV 3
P698.1 Src SCI DigOut 1
P698.2 Src SCI DigOut 2
P698.3 Src SCI DigOut 3
P698.4 Src SCI DigOut 4
P704.3 SCom TlgOFF SCB
P796 Compare Value
P797 Compare Hyst
P049.4 OP OperDisp
9-6
Factory
setting with setting with
PMU
P366 = 0
BICO1 BICO2 BICO1
(i001) (i002) (i001)
KK058 KK040 KK040 KK040 KK040 KK040 KK058 KK040 KK058 K4102
B0005 B0022 B2100 B0022 B2100 B0022 B0005 B0022 B2100 B4100
B0001 B0020 B0001 B0020 B0001 B0001 B0001 B0001 B0001 B0001
B0001 B0001 B0001 B0001 B0001 B0001 B0001 B0001 B0001 B4108
B2107 B2107 B2107 B2107 B2107 B2107 B2107 B2107 B2107 B2107
B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0000 B4107 B4107
B0000 B0018 B0000 B0018 B0000 B0010 B0000 B0010 B0000 B0000
B0000 B0000 B2108 B0000 B2108 B0000 B0000 B0000 B0000 B0000
B0001 B0001 B2111 B0001 B2111 B0001 B0001 B0001 B2111 B4129
B0001 B0001 B2112 B0001 B2112 B0001 B0001 B0001 B2112 B4109
B0008 B0000 B0000 B0000 B0000 B0000 B0008 B0000 B2113 B4105
B0009 B0000 B0000 B0000 B0000 B0000 B0009 B0000 B2114 B4106
B0001 B0001 B0001 B0001 B0018 B0018 B0018 B0018 B0018 B0018
B0001 B0001 B0001 B0001 B0020 B0020 B0020 B0020 B0020 B0020
B0014 B0014 B0014 B0014 B0012 B0012 B0012 B0012 B4102 B4102
B0107 B0107 B0107 B0107 B0000 B0000 B0000 B0000 B0107 B0107
B0104 B0104 B0104 B0104 B0000 B0000 B0000 B0000 B0104 B0104
B0000 B0000 B0000 B0000 B0107 B0107 B0107 B0107 B0000 B0000
K0000 K0000 K0000 K0000 K0000 K0000 K0000 K0000 KK020 KK020
K0000 K0000 K0000 K0000 K0000 K0000 K0000 K0000 K0022 K0022
K0000 K0000 K0000 K0000 K0000 K0000 K0000 K0000 K0024 K0024
B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0100 B0100
B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0120 B0120
B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0108 B0108
B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0000 B0107 B0107
0 ms 0 ms 0 ms
100.0 100.0 100.0
3.0 3.0 3.0
r229 r229 P405
Table 9-5 Factory setting dependent on P366
All other factory setting values are not dependent on P366 and can be
taken from the parameter list or from the block diagrams (in the
Compendium).
The factory settings for Index 1 (i001) of the respective parameter are
displayed in the parameter list.
Factory Cabinet unit
with
OP1S OP1S or
terminal strip
P366 = 1 P366 = 2
BICO2 BICO1 BICO2
(i002) (i001) (i002)
0 ms 0 ms 0 ms
100.0 100.0 100.0
3.0 3.0 3.0
P405 P405 P405
Operating Instructions
04.2006
Cabinet unit Cabinet unit
with PMU or with NAMUR
terminal strip terminal strip
P366 = 3
BICO1 BICO2 BICO1
(i001) (i002) (i001)
0 ms 0 ms 100 ms 100 ms
100.0 100.0 2.0
3.0 3.0 1.0
r229 r229 r229
6SE7087-6KD60 Siemens AG
SIMOVERT MASTERDRIVES
(SCI)
P366 = 4
BICO2
(i002)
2.0
1.0
r229