Technical Data; Before Starting The Equipment; Attachment And Operation; Mains Connection - Scheppach 5906103901 Original Bedienungsanleitung

Do not lose these safety instructions

6. Technical data

Mains connection

Motor rating W
Operating mode
Compressor speed
Pressure vessel capacity
liters)
Operating pressure
Theoretical intake capacity (l/min)
sound power level L
WA
uncertainty K
WA
Protection type
Weight of the unit in kg
Oil (15W 40) l
Max. altitude
(above mean sea level)
The noise emission values were measured in ac-
cordance with EN ISO 3744.
Wear hearing protection.
The effects of noise can cause a loss of hearing.

7. Before starting the equipment

• Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
• Prior to initial commissioning, remove the trans-
port plug (E) and fill the crank housing with oil as
described in item 8.4.
• Check the equipment for damage which may have
occurred in transit. Report any damage immedi-
ately to the transport company which was used to
deliver the compressor.
• Install the compressor near the point of consump-
tion.
• Avoid long air lines and supply lines (extension
cables).
• Make sure that the intake air is dry and dustfree.
• Do not install the compressor in a damp or wet
room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient tem-
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma-
ble gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.
40 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
All manuals and user guides at all-guides.com
230 V ~ 50 Hz
1100
S1
2850 min
-1
(in
50
approx. 8 bar
approx. 220
93 dB(A)
3 dB
IP20
approx. 31
approx. 0,25
1000 m
• The oil level in the compressor pump has to be
checked before putting the equipment into opera-
tion.

8. Attachment and operation

m Important!
You must fully assemble the appliance before using it
for the first time!
8.1 Fitting the wheels (Fig. 5)
• To attach the wheels (12), pass a washer with the
wheel bolt through the wheel. Then add a wash-
er and a hexagon nut on the inside of the wheel.
Fasten the nut by hand so that the wheel still can
be rotated.
• Push the wheel unit through the ear below the
tank.
• Fasten it with a washer, a safety washer and a nut
and tighten them securely.
• Repeat this process with the second wheel.
8.2 Fitting the supporting foot (Fig. 4)
• Attach the rubber feet on the ear at the bottom of
the tank's front side using the screws, washers
and nuts provided.
8.3 Fitting the air filter (Fig. 6)
• Warning: The air filter must be installed before the
initial use. Using the device without air filter will
damage the compressor and void the warranty.
• Remove the transportation stop (G) and screw the
air filter (15) to the equipment.
8.4 Changing the transportation cover (B)
(Fig. 9,10)
• Remove the transport lid (E) of the oil filling open-
ing (F).
• Fill the included compressor oil into the crank
housing and insert the included oil sealing plug
(14) into the oil filling opening (F).
• Check the oil level in the sight glass (16). The oil
level should be in the centre of the red circle.
8.5 Mains connection
• The compressor is equipped with a mains cable
with shock-proof plug. This can be connected to
any 230 - 240V ~ 50 Hz shock-proof socket.
• Before you use the machine, make sure that the
mains voltage is the same as the operating voltage
(see the rating plate).
• Long supply cables, extensions, cable reels etc.
cause a drop in voltage and can impede motor
start-up.
• At low temperatures below +5°C, sluggishness
may make starting difficult or impossible.