Scheppach HS110 Original Bedienungsanleitung Seite 29

7. Use the right tool
- Do not force small tools to do the job of a heavy
tool.
- Do not use the power tool for such purposes for
which it is not intended. Use for example no cir-
cular saws to cut tree branches or logs.
- Do not use the electric tool to the firewood saws.
8. Dress properly
- Do not wear loose clothing or jewellery, they can
be caught in moving parts.
- Non-skid footwear is recommended when work-
ing outdoors.
- Wear protective hair covering to contain long hair.
9. Use protective equipment
- Use safety glasses.
- Use face or dust mask if working operations cre-
ate dust.
10. Connect dust extraction equipment
- If the tool is provided for the connection of dust
extraction and collecting equipment, ensure
these are connected and properly used.
- Indoor operation is permitted only with a suitable
extraction system.
11. Do not abuse the cord.
- Never yank the cord do disconnect it from the
socket. Keep the cord away from heat, oil and
sham edges.
12. Secure work
- For long workpieces, an additional supporting
surface (table, trestles, etc.) is required in order
to prevent tipping of the machine.
- Always press the workpiece firmly against the
working surface and stop in order to prevent
wobbling or twisting of the workpiece.
13. Do not overreach
- Keep proper footing and balance at all times.
- Avoid awkward hand positions in which one or
both hands could touch the saw blade as the re-
sult of a sudden slip.
14. Maintain tools with care
- Keep cutting tools sharp and clean for better and
safer performance.
- Follow instruction for lubricating and changing
accessories.
- Inspect tool cords periodically and if damaged
have them repaired by an authorized service fa-
cility.
- Inspect extension cords periodically and replace
if damaged.
- Keep handles dry, clean and free from oil and
grease.
15. Disconnect tools
- Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
- When the electric tool is not in use, before main-
tenance and when changing tools such as the
saw blade, drill bit, milling cutter.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
16. Remove adjusting keys and wrenches
- Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
17. Avoid unintentional starting
- Ensure switch is in "off" position when plugging
in.
18. Use outdoor extension leads
- When the tool is used outdoors, use only ex-
tension cords intended for outdoor use and so
marked.
- Use the cable drum only in the unrolled state.
19. Stay alert
- m Watch what you are doing, use common sense
and do not operate the tool when you are tired.
20. Check damaged parts
- Before further use of tool, it should be carefully
checked to determine that it will operate properly
and perform its intended function.
- Check whether the moving parts are working
properly and are not becoming jammed or wheth-
er parts are damaged. All parts must be correct-
ly fitted and satisfy all conditions to ensure the
proper operation of the power tool.
- The movable guard must not be clamped when
it is open.
- A guard or other part that is damaged should be
properly repaired or replaced by an authorized
service centre unless otherwise indicated in this
instruction manual.
- Have defective switches replaced by an author-
ized service centre.
- Do not use any faulty or damaged connection
cables.
- Do not use the tool if the switch does not turn it
on and off.
21. WARNING!
- The use of any accessory or attachment other
than one recommended in this instruction manu-
al may present a risk of personal injury.
22. Have your tool repaired by a qualified person
- This electric tool complies with the relevant safe-
ty rules. Repairs should only be carried out by
qualified persons using original spare parts, oth-
erwise this may result in considerable danger to
the user.
Additional safety instructions
1. Safety Precautions
• m Warning! Do not use damaged, cracked or de-
formed saw blades.
• Replace a worn table insert.
• Only use saw blades recommended by the manu-
facturer which conform to EN 847-1.
GB | 29