Руководство по эксплуатации
7.5.1 Сохранение профиля колеса
На станке можно сохранить до 9 профилей колес.
• Установите колесо, профиль которого необходимо
сохранить.
• Определите все необходимые данные колеса,
включая
количество
необходимости функции EasyAlu, Easy Alu Toggle
и Alu P.
• Нажмите клавишу F6 на экране ВОДА ДАННЫХ
ДИСКА и выберите опцию профиля колеса (1, Рис.
7-23).
Откроется окно ПРОФИЛЯ КОЛЕСА (Рис. 7-24).
Текущие параметры профиля колеса будут
выделены внизу данного окна.
•
Выберите прокруткой одну из 9 позиций списка
для сохранения текущего профиля.
• Нажмите клавишу F3 для подтверждения ввода.
После этого, данные будут сохранены, и потом их
можно будет повторно использовать.
Примечание:
Если данные записываются поверх старого профиля,
то он больше не отображается в списке.
7.5.2 Использование сохраненного профиля
колеса
• Установите колесо на станок.
• Нажмите клавишу F6 на экране ВВОДА ДАННЫХ
ДИСКА и выберите опцию профиля колеса (1,
Рис. 7-23).
Откроется окно ПРОФИЛЯ КОЛЕСА (Рис. 7-24).
• Выберите прокруткой профиль для установленного
колеса.
• Нажмите клавишу F5 для подтверждения выбора.
Откроется окно ВВОДА ДАННЫХ ДИСКА (Рис. 7-
25) с отображением данных выбранного профиля.
• Проверьте правильность данных в поле
состояния и окне статуса.
Станок готов к выполнению измерительного цикла
(раздел 8.1).
BFH 2000
All manuals and user guides at all-guides.com
спиц,
используя
при
Operation - MANUAL
7.5.1 Saving a Wheel Profile
Up to 9 wheel profiles can be saved.
• Clamp the wheel you wish to save the profile of.
•
Set and acquire all the wheel data including the number
of spokes and the EasyAlu and Easy Alu Toggle
readings if an Alu P is required.
• Press the menu key F6 in the ENTERING RIM DATA
screen and select the Wheel Profiles item (1, Fig. 7-
23).
The WHEEL PROFILES screen (Fig. 7-24) will open.
The current wheel profile data is highlighted in a line on
its own at the bottom of the page.
•
In the 9 position list, use the Scroll command to
choose the current profile registration position.
• Press the F3 key to save data.
The data is now saved permanently in the chosen position
and can be recalled when required.
Note:
If the profile is overwritten with other data it is no longer
shown in the list.
7.5.2 Recalling a Wheel Profile from the
memory
• Clamp the wheel to the balancer.
•
Press the Menu key F6 in the ENTERING RIM DATA
screen and then select and press the WHEEL
PROFILES key (1, Fig. 7-23).
The WHEEL PROFILES screen (Fig. 7-24) will open.
•
Use the Scroll command to select the profile indicated
for the wheel on the machine.
• Press the F5 key to apply the data selected.
The ENTERING RIM DATA screen (Fig. 7-25) will open
and show the data recalled.
• Check that the settings in the Indications Field and
Status Bar panel are correct.
The machine is now ready to proceed with the measuring
run (Chapter 8.1).
93