Features; Indications; Identifi Cation Of Parts; Setup - gc D-Light Pro Bedienungsanleitung

intervals. The Low Power mode (LP) can also be used to
limit heat generation when close to the pulp.
• If the handpiece is not used for an extended period of
time, or the unit is being transported, then the battery
should be removed from the handpiece or charging
station.
• Maintain adequate infection control measures when using
the D-Light Pro in the oral cavity, and execute the
appropriate hygiene plan after usage with patients.
• Protect the D-Light Pro from contamination by using
protective plastic barrier-sleeves. These sleeves are
intended for single-use; discard after each patient to
prevent possible cross-contamination. Protective plastic
barrier-sleeves are not needed when the light-guide and
handpiece sleeve are autoclaved between each patient.
• When using protective plastic barriers (bags, shields, etc.)
with the D-Light Pro, be certain that these are securely
affi x to avoid patient aspiration and treatment
complications.
• Do not use the Detection mode (DT) in conjunction with
caries detection dyes.
• Do not use if you have red-green color blindness or visual
impairment.

2. FEATURES

• LED powered visible light curing and visualisation unit
with high power output
• The D-Light Pro can polymerize light cured dental
materials, quickly and effi ciently.
• The D-Light Pro contains two diff erent types of LEDs
with diff erent wavelength peaks. This enables the
D-Light Pro to activate commonly used photo initiators
used in dentistry, like Camphorquinone (wavelength
peak of 468 nm) used in most light-cured materials, and
other initiators (wavelength peak of 400 +1-20 nm)
used in some light-cured dental materials.
• The D-Light Pro Detection mode (DT) assists the
visualisation of bacteria in plaque and carious lesions
and the identifi cation of fl uorescent materials.
• The D-Light Pro off ers an easy-to-use and elegant
stainless steel design. The design ensures a
user-friendly operation of the unit.
• Lithium polymer batteries, when fully charged, allow
for more than 45 individual irradiations of 20 seconds
duration each. The lithium polymer battery has no
memory eff ect, and a fast recharging speed of 75
minutes.
• The D-Light Pro is designed to off er a stable and
continuous high light output over several years.
• Built-in radiometer
• In addition to the light guide, the handpiece is
autoclavable once the internal electronic module and
battery pack have been removed.
• The D-Light Pro is under warranty for a period of 3
years, except the battery (1 year warranty) and
consumables (no warranty).

3. INDICATIONS

• Polymerisation of visible light curing materials curing
with a wavelength range of 400 to 480nm. In case of
questions about the wavelength ranges for certain
materials, please contact their respective
manufacturers.
• The Detection mode (DT) assists the visualization of
bacteria in plaque, fi ssures, infected dentin and the
presence of micro-leakage. It also helps to identify
fl uorescent restorative materials, and to evaluate the
depth of cracks in the tooth structure.
4. IDENTIFICATION OF PARTS
• Handpiece
• Electronic module
• Battery packs (x2)
• Light-guide
• Soft eye-protector shields (x3)
• Hard, oval eye-protection shield
• Charging station
• Power supply and cable
• EU/UK plug adapters

5. SETUP

• Carefully unpack all D-Light Pro components and
familiarize yourself with the individual items. Check for
completeness.
• First, check that the voltage indicated on the D-Light Pro
charging station name plate complies with the local
power supply.
Battery
• Prior to initial use or use after a long interval of non-use,
be sure to charge or recharge the batteries completely.
Use the original charging station and lithium polymer
battery only. Do not use any other battery chargers or
batteries.
• Connect the power cord to the charging station, and the
plug of the power cord to the mains power outlet
(110-240V AC) (Figure 8)
• Insert the batteries fully onto the docking ports of the
charging station until you hear/feel a 'click' (Figure 9)
• There is a LED corresponding to each docking port.
When the LED is illuminated, the battery is in the process
of being charged. When the LED turns off , then charging
is completed. Two batteries can be simultaneously
charged.
• Do not connect the depleted battery pack to the
charging station until it is properly cleaned and
disinfected.
• The time to fully charge an empty battery is
approximately 75 minutes.
• When the D-Light Pro is not in use for a prolonged
period of time, the battery pack should be disconnected
from the handpiece; or the handpiece/battery should be
in the "off " position.
• Batteries may be stored on the docking ports of the
charging station as long as there is power to the
charging station.
® EN
D-Light Pro
DE
FR
IT
ES
NL
DA
SV
NO
PT
Figure 1
Figure 2
FI
Figure 3
EL
Figure 4
Figure 5
Figure 5
Figure 6
Figure 6
Figure 7
3