Scope Of Delivery And Optional Accessories - Benning ST 725 Bedienungsanleitung

It may be assumed that safe operation is no longer possible:
- if the instrument show visible signs of damage
- if the appliance tester no longer functions
- after long periods of storage under unfavourable conditions
- after being subjected to rough transport
- the device is exposed to moisture.
In order to prevent danger
- do not touch the bare measuring probe tips of the measuring leads,

- plug the leads into the correspondingly marked jacks at the measuring
instrument
Maintenance:
Do not open the tester, because it contains no components which can be

repaired by the user. Repair and service must be carried out by qualified
personnel only!
Cleaning:

Regularly wipe the housing by means of a dry cloth and cleaning agent. Do not
use any polishing agents or solvents!
3.

Scope of delivery and optional accessories

The scope of delivery for the BENNING ST 725 comprises:
3.1 One BENNING ST 725,
3.2 One test lead with alligator clip,
3.3 One IEC power cord (IEC adapter cable)
3.4 One mains connection cable
3.5 One compact protective pouch,
3.6 One USB connecting cable (A plug to Micro-B plug),
3.7 Six 1.5-V-batteries/ type AA (IEC LR6) fitted in the unit as initial equipment,
3.8 One operating manual
3.9 One CD-ROM with download/driver software, multilingual operating manual and
information material
Parts subject to wear:
- The BENNING ST 725 is provided with two fuses for overload protection:
two fuses with a nominal current of 16 A, 250 V, F, breaking capacity ≥ 500 A, D = 5 mm, L =
20 mm (part no. 10019440)
- The BENNING ST 725 is supplied by six 1.5 V batteries/ type AA (IEC LR6).
Note on optional accessories:
- Portable printer BENNING PT 1 for printing test records rapidly on site, direct thermal
printing process, incl. Mains supply unit and rechargeable Ni/MH battery pack (044150)
- Rolls of thermographic paper (20 pieces), roll width / length: 58 mm /13 m (044151)
- Test badges "next test", 300 pieces (756212)
Passive measuring adapters:
- Measuring adapter for three-phase loads (passive, without mains voltage-dependent
switching devices) for R
measurements:
- 16 A CEE coupling (5-pin) - shock-proof plug (044122)
- 32 A CEE coupling (5-pin) - shock-proof plug (044123)
- 16 A + 32 A CEE coupling (5-pin) + 16 A CEE coupling (3-pin) - 16 A shock-proof plug
(044147)
- 16 A CEE coupling (3-pin) - 16 A shock-proof plug (044143)
- 32 A CEE coupling (3-pin) - 16 A shock-proof plug (044144)
Active measuring adapters:
- Measuring adapter for three-phase loads (active, with mains voltage-dependent switching
devices) for R
PE
- 16 A CEE adapter (5-pin), active (044140)
- 32 A CEE adapter(5-pin), active (044141)
As an alternative:
- BENNING CM 9 leakage current clamp for measuring the differential current, protective
conductor current and load current of single-phase and three-phase loads (044065)
- Measuring adapter for BENNING CM 9 leakage current clamp, conductors led through
individually, with double insulation:
- 16 A shock-proof coupling - 16 A shock-proof plug (044131)
- 16 A CEE coupling (5-pin) - CEE plug (5-pin) (044127)
- 32 A CEE coupling (5-pin) - CEE plug (5-pin) (044128)
09/ 2014
, R (insulating resistance) and I
PE ISO
and I measurements (direct measurement) under operating conditions:
PE
BENNING ST 725
(alternative leakage current)
EA

22