Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Fig.
e
Mount the retaining clips (95) for the tension-
ing bars (92) in the rectangular holes of the angle
frame (1R) and clip in the tensioning bars (92).
4.7
Mounting the rear-mounted torsion
spring shaft (HL)
Note that the following instructions only describe the
differences to the assembly of the front-mounted tor-
sion spring shaft (VL version). If the assembly steps
are identical to the VL version, there is only a refer-
ence to the respective assembly chapter of the VL
version. Follow the assembly instructions for the VL
version on the respective passages.
4.7.1 HL – Preassembling the door frame
Follow the instructions and Fig.
chapter: 4.4.1 - Preassembling the door frame.
Note that Fig.
b
only refers to the VL variant and
does not apply here.
4.7.2 HL – Mounting the wall anchors
Follow the instructions and illustrations of chapter:
4.4.2 - Mounting the wall anchors.
4.7.3 HL – Mounting the plugs for the door
frame
Follow the instructions and illustrations of chapter:
4.4.3 - Mounting the plugs for the door frame.
In Fig.
e
, Page A5., observe the HL version: The
angle frame (1R/1L) is screwed on the garage wall by
means of one screw (S8) and the suitable plug (S9).
4.7.4 HL – Preassembling the horizontal rail
pairs
Follow the instructions and illustrations of chapter:
4.4.4 - Preassembling the horizontal rail pairs.
Observe the following differences with regard to the
VL version:
Fig.
c
, Page A6. In addition, mount one fastening
profile (100) each to the horizontal rail pair (14R/14L)
by means of the screws (S6) and (S12). In doing so,
note that the screw heads (S6) are mounted towards
the inside to the rail!
Fig.
e
Mount the HL sole plate (21R/21L) to the rail
pair (14R/14L). Use the screws (S6) and (S12) for
this purpose, too.
4.7.5 HL – Mounting the rail pairs to the frame
Follow the instructions and illustrations of chapter:
4.4.5 - Mounting the horizontal rail pairs to the frame.
4.7.6 HL – Suspending the horizontal rail pairs
Follow the instructions and illustrations of chapter:
4.4.6 - Suspending the horizontal rail pairs.
Observe the following differences with regard to the
VL version:
Fig.
d
Using two screws (S6 + S12) each, mount the
rail connector (6) to the HL sole plate (21L/21R) of
both rail pairs (14R/14L).
26 - EN
Fig.
anchor rail (27), the connection angle (28) and the
screws (S6 + S12). Only fasten the screws lightly to
be able to align the system afterwards. Then use two
screws each (S6 + S12) to mount the preassembled
ceiling suspension to the HL sole plate (21L/21R).
4.7.7 HL – Preassembling the centre bearing
Fig.
the base plate (103) by using the screws (S6 + S12).
Fig.
position the rail clips in the rail connector (6).
Fig.
ing (37) to the rail clips (29) with the nuts (S12) and
ensure that the centre bearing can still be shifted.
a
, Page A3. of
NOTICE
4.7.8 HL – Mounting the torsion spring shaft
Follow the instructions and illustrations of chapter:
4.4.7 - Mounting the torsion spring shaft.
Fig.
sembled right torsion spring shaft (35R) into the sole
plate (21R) and fasten it using the screw (S11).
Fig.
the torsion spring shaft (35R) and tighten the
screws (S12). Observe the following:
•
•
Fig.
the right torsion spring shaft (35R).
Fig.
same way you mounted the right. Then centrally slide
the shaft coupling (38) over both shaft ends. Only
fasten lightly in order to guarantee a subsequent ad-
justment.
Fig.
ing.
4.7.9 Hl – Replacing the wire rope
Fig.
the HL holder for the deflection roller (101R/101L) to
the tail end (16R/16L) and the fastening profile (100).
Fig.
drum (106). Remove the wire rope (104) by loosening
the grub screw from the cable drum (106) and dis-
pose of the wire rope.
Fig.
drum (106) to the HL sole plate (21R/21L) using the
screws (S10).
f
Mount the ceiling suspension consisting of the
a
, Page A11. Screw the centre bearing (37) to
b
Insert the screws (S5) in the rail clip (29) and
c
Lightly screw the preassembled centre bear-
Doors with a width of basic
dimension exceeding 3530 mm
require two centre bearings (37).
Mount one centre bearing (37) per side
and per torsion spring (35R/L) to the rail
connector (6).
a
and Fig.
b
, Page A12. Slide the preas-
c
and Fig.
d
Slide the centre bearing (37) onto
Ensure a sufficient distance to the torsion spring
shaft (35R) which should at least be 120 mm.
Also consider to leave sufficient space for the
shaft coupling (38) and its installation.
f
Slide the shaft coupling onto the shaft end of
g
Mount the left torsion spring shaft (35L) the
i
Mount a ceiling suspension to the centre bear-
a
, Page A15. Use the screws (S11) to mount
b
Unreel the wire rope (104) from the cable
c
Mount the protective cover for the cable
Werbung
Kapitel
Inhaltsverzeichnis
