Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4.4.4 Preassembling the horizontal rail pairs
Fig.
a
, Page A6. Connect the horizontal rail
pairs (14R/14L) with the tail end (16R/16L) by using
the screw (S15).
Fig.
b
Mount the connecting plate (18). In doing so,
note that the screw heads (S6) are mounted towards
the inside to the rail!
Fig.
d
Mount the track bracket for the rail (19) by pla-
cing it on the centre of the rail pairs (14R/14L) and by
turning it into position.
Fig.
e
Mount the corner connection brackets (20) to
the rail pair (14R/14L).
4.4.5 Mounting the horizontal rail pairs to the
frame
Fig.
a
, Page A7. Connect the rail pairs (14L/14R)
to the angle frame (1L/1R) by lightly screwing it to the
tail end (16L/16R) with the angle frame (1L/1R). It
should still be possible to fold up the system later on.
For adjusting, proceed as follows:
Fig.
b
If the width stop exceeds 120 mm, insert the
screw (S5) through the addendum angle of the frame,
then through the rectangular-shaped hole in the tail
end (16R/16L). Lightly fasten it with the nut (S12).
Fig.
c
If the width stop size is smaller: Should the
screw (S5) be pre-assembled, also see chapter: 4.4.2
- Mounting the wall anchors (Fig.
4.4.6 Suspending the horizontal rail pairs
Fold up the horizontal rail pairs (14R/14L) and secure
them against folding back.
Fig.
a
, Page A8. Mount the rail arches (30) by
screwing them to the angle frames and to the con-
necting plates (18) by means of the screws (S17 +
S12).
NOTICE
Potential obstruction at the transition
to the rails.
Make sure there is no offset in the
transition between the guide rails. If ne-
cessary, slightly adjust the arch ends.
Fig.
b
Screw the tail end (16) with the screw (S11) to
the addendum angle.
Suspending the rail pairs (14R/14L) at the rear can
be carried out in two assembly versions, depending
on the material conditions.
Procedure for wall mounting if internal width of the
garage is up to max. width of basic dimension +
1030 mm for a central installation of the door:
Fig.
c
In a first step, prepare an anchor rail (27),
measure the required length and shorten the anchor
rail (27) accordingly. In doing so, note that ap-
prox. 200 mm have to be added to the required
measurement which will later remain in the rail con-
nector (6) and which provide for the required stability.
In a next step, mount a rail clip (29) to one end of the
anchor rail (27). While screwing it on, make sure the
rail clip is able to move freely. Then mount the con-
nection angle (28) to the other end. Use the
screws (S6 + S12) for assembly. On the side of the
wall mounting, completely slide the preassembled an-
chor rail (27) into the rail connector (6).
Fig.
rail
bracket (20) of both rail pairs (14R/14L). It is best to
use the upper hole for the screw connection. Excep-
tion: The drive requires the lower hole for assembly.
Fig.
from the rail connector (6) and screw the preas-
sembled anchor rail (27) to the garage wall by means
of the screws (S8, S9). Only fasten the rail clip (29)
lightly. It should still be possible to shift the anchor
rail (27) in order to align it diagonally afterwards.
Procedure for ceiling mounting if internal width of the
garage exceeds width of basic dimension + 1030 mm
for a central installation of the door:
Fig.
rail
bracket (20) of both rail pairs (14R/14L). It is best to
use the upper hole for the screw connection. Excep-
tion: The drive requires the lower hole for assembly.
Fig.
shortened accordingly. The ceiling suspension con-
sists of the anchor rail (27), the connection angle (28)
c
).
and the screws (S6 + S12). Only fasten the screws
lightly to be able to align the system afterwards. Then
use two screws each (S6 + S12) to mount the preas-
sembled ceiling suspension to the corner connection
brackets (20).
Fig.
plugs (S9) to mount the ceiling suspension to the gar-
age ceiling.
Fig.
guide rails. To do so, select the same reference
points for both sides. Both diagonals need to have
the same value to ensure a smooth door movement
with low friction. If required, also check the horizontal
alignment of the rail pairs by means of a spirit level.
Only then tighten the screws on the ceiling suspen-
sion.
Fig.
sisting of the anchor rail (27), the connection
angle (28) and the screws (S6 + S12). Screw the ceil-
ing suspension with the screws (S6 + S12) to the rail
pairs (14R/14L), to the front of the connecting
plate (18) and to the centre of the track bracket for
the rail (19).
Fig.
twisting, then screw the remaining ceiling suspen-
sions to the garage ceiling by means of the
screws (S8) and the suitable plugs (S9).
Fig.
suspension, install an additional diagonal strut.
d
Using two screws (S6 + S12) each, mount the
connector (6)
to
the
e
Pull out the preassembled anchor rail (27)
d
Using two screws (S6 + S12) each, mount the
connector (6)
to
the
f
Mount the ceiling suspension that has been
g
Then use the screws (S8) and the suitable
h
Measure the diagonals of both horizontal door
i
Mount the remaining ceiling suspensions con-
j
Check the rail pairs (14R/14L) for potential
k
In case of stability problems of the rear ceiling
corner
connection
corner
connection
EN - 23
Werbung
Kapitel
Inhaltsverzeichnis
