CleanSpace HALO CS3000 Bedienungsanleitung Seite 27

1. Non-Alcohol Disinfectant or Cleaning Wipes
•
Non-alcoholic cleaning wipes are impregnated with benzalkonium chloride, a bactericidal solution ideally suited
for face pieces that are going to be worn in the near term/same day.
•
Wipes containing alcohol or more stringent cleaning agents should be avoided if the mask is not going
to be washed before being worn.
•
Wipe the mask, head harness and neck support inside and out.
•
For the mask exhalation valve, with the valve cover removed (using the instructions above), gently lift and wipe
the leaf edge. When finished Replace the valve cover before use by snapping the cover back in place.
2. Warm soapy water or an industrial washer
•
The mask, head harness and neck support can be washed with a mild detergent in warm water or an industrial
washer.
•
Use water and drying temperatures less than 50°C.
•
For hand washing use a soft brush or sponge to remove stubborn dirt or grit.
•
For the mask exhalation valve, with the valve cover removed (using the instructions above), gently wash the
warm water solution through the valve and use a sponge to gently clean the valve surface
•
Rinse the mask, head harness and neck support thoroughly in fresh water to remove cleaning residue.
IMPORTANT: Not rinsing the mask thoroughly, may result in residue from cleaning solution causing
irritation to the wearer's skin or may cause the exhalation valve to stick.
•
Replace the mask exhalation valve cover before use.
Drying the mask
•
After cleaning, allow the mask, head harness and neck support to air dry in a clean environment away from
sunlight. Position the mask with the valve facing up to prevent water pooling.
•
Do not dry the mask, head harness and neck support by exposing directly to heat i.e. hair dryers or heaters.
The mask can also be hand-dried with a clean, lint-free cloth.
•
IMPORTANT: Cleaning can cause the exhalation valve leaf to stick. Before use, check that the
exhalation valve leaf operates freely by gently lifting the valve. Replace the mask exhalation valve
cover before use.
WARNING: NEVER DRY THE MASK OR EXHALATION VALVE WITH A CLOTH THAT MAY LEAVE BEHIND LINT.
Lint contamination of the exhalation valve may cause it to leak, resulting in overexposure to
CLEANING THE RESPIRATOR
•
Removing the mask, head harness and neck support. Remove the used filter.
•
IMPORTANT: Insert the CleanSpace Halo Cleaning & Storage Plug (CS3011) into the filter inlet and two
bellow air outlets. Using the Cleaning & Storage Plug (CS3011) prevents dust or liquids from entering the air
path of the respirator.
•
Cleaning wipes or a cloth soaked with cleaning agent, can be used to wipe down the outside of the respirator.
After cleaning, use a clean cloth to remove the cleaning agent.
•
Allow the respirator to air dry in a clean environment. The respirator can also be dried with a clean lint-free
cloth. Note: Do not dry the respirator by exposing to heat (i.e. hair dryers or heaters) or compressed air.
•
When dry, store the Respirator with the Cleaning Storage Plug (CS3011) in place to prevent dust and
liquids entering the air path of the respirator.
•
If the respirator is to be used immediately after cleaning, insert a clean filter and lock in place ready for
use.
WARNING: The respirator contains a battery, sensitive electronics and a motor. NEVER
WARNING: NEVER CLEAN THE FILTER WITH COMPRESSED AIR OR A BRUSH. FILTERS ARE EASILY
Misuse of CleanSpace Respirators by cleaning the filter may result in overexposure to
contaminants and lead to sickness or death
immerse it in water or use anything wetter than a damp cloth to clean it.
DAMAGED BY THE USE OF WATER, COMPRESSED AIR OR BY BRUSHING.
contaminants and lead to sickness or death
27
.
.