Programming The Clearray - Jacuzzi J-200 Serie Montageanweisung Und Bedienung Und Wartung

I
Economy filtering/heating modes
(the heater is activated only during the filtering cycles)
F4: 1 hour of filtering/heating per day
(one half-hour cycle every 12 hours)
F5: 1 1/2 hours of filtering/heating per day
(a half-hour cycle every 8 hours)
F6: 2 hours of filtering/heating per day
(one half-hour cycle every 6 hours)
I
Lock modes
see "filtering mode for models without circulation pump"
I
Programming the Circulation Pump Filtration Cycle
(For Spas Equipped with a Circulation Pump)
Press and hold the Jets pump 1 (
the same time for 3 seconds to access the circulation pump
programming. Once you have entered the circulation pump fil-
tration cycle, continually press the Warmer (
up through the cycles below. Then select a cycle and press the
Jets pump 1 ( ) button to activate that cycle. Upon pressing
1
the jets pump 1 button the system will save your selection, exit
the program menu and return to the main menu.
Note: After 10 seconds the programming screen will revert
back to the temperature if no buttons are pressed. You cannot
have more than one circulation pump cycle activated at a time.
0 hours of circulation per day
4 hours of circulation per day
8 hours of circulation per day
12 hours of circulation per day
16 hours of circulation per day
20 hours of circulation per day
24 hours of circulation per day
(recommended factory default setting)
Note: The recommended factory default setting for the J200
Collection is 24 hours. This setting should not be altered. Run-
ning the circulation pump less than the factory recommended ti-
me might result in issues with water quality maintenance.
) and Cooler ( ) button at
1
) button to scroll
Programming the Clearray (Ultraviolet)
Programming the CLEARRAY System (U) or Corona Di-
scharge Ozone (O3) (where included)
Press and hold the Jets pump 1 (
at the same time for 3 seconds. Scroll pass the circulation pump
programming menus by pressing the Warmer button.
Menus for spas equipped with a circulation pump.
Press Press
Press
Press
Will select "03"
Will select "O3"
1
option and exit
option and exit
menu
menu
Press
Press
Will take you back to
Will take you back
"C0" option
to "C0" option
Menus for spas NOT equipped with a circulation pump.
Press
Press
or
or
Note: If your spa is not equipped with a circulation pump you
will not need scroll through the circulation pump programming
menus. You will enter the sanitizing system program.
After the last cycle, "C6", the LED screen will display "U" or "O3".
If the LED screen is displaying "U" then pressing the Jets pump
1 will change the sanitizing system from "U" to "O3" and exit the
programming menu. If the LED screen is displaying "O3" then
pressing the Jets pump 1 will change the sanitizing system from
"O3" to "U" and exit the programming menu. You will see one of
the two configurations below:
A. C0, C1, C2, C3, C4, C5, C6, U, 365 (duration countdown ti-
mer)
B. C0, C1, C2, C3, C4, C5, C6, O3, =
Note: For the O3 option the "=" disables the duration countdown
timer.
If you do not wish to change the option do not press any buttons
and after 10 seconds the display will return to the main menu.
Note: If the CLEARRAY System has been selected, when the
time allotted has expired (365 days) the display screen will fla-
sh between the water temperature and "blb". At this time the
UV lamp bulb must be replaced, the quartz tube must be clea-
ned and the duration countdown timer needs to be reset.
Resetting the duration countdown timer (CLEARRAY™ Sy-
stem only)
Once the duration countdown timer for the CLEARRAY System
has reached zero, you will need to reset it, replace the UV lamp
bulb and clean the quartz tube.
24
) and Cooler ( ) button
1
Press Press Press
Press
Press Press
Press Press
Press
Press
Press
Press
or or