Herunterladen Inhalt Inhalt Diese Seite drucken

Electrical Safety; Start-Up Instructions - Jacuzzi J-200 series Montageanweisung Und Bedienung Und Wartung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 52
I
The spa is not intended for use in public places; always check
for any restrictions and/or regulations concerning the installation
and use of the apparatus in the area chosen.

Electrical safety

The spa are safe products, manufactured in compliance with
standards
60335-1: 2002, 60335-2-60: 2003, 60825-1:
1994+A1+A2, EN 55014-2, CISPR 22 CLASS B, EN 61000-
and tested during production to ensure user
3-2, EN 6100-3-3
safety.
I
Installation must be performed by qualified personnel who
ensure compliance with current national regulations and who
are also authorized to issue a certificate of compliance with
proper installation procedures.
It is the responsibility of the installer to select ma-
terials based on their intended use, to carry out
work properly, to check the condition of the system
that the unit will be connected to and that it en-
sures safety of use also concerning maintenance
work and the possibility to examine the system.
I
The spa are class "I" appliances and therefore they must be
permanently connected, without any intermediate connec-
tions, to the electrical system and to the protection system
(earth system).
The electrical system of the building must be provid-
ed with a 0.03A differential switch and with an effi-
cient protection (earth) circuit. Check for proper oper-
ation of the differential switch by pressing the TEST
button, which should trip.
Parts incorporating electrical components, except
remote control devices, must be located or fixed
so that they cannot fall into the spa. Live compo-
nents and equipment must be out of reach of indi-
viduals in the spa.
I
For connection to the electrical mains, it is necessary to install an
omnipolar cut-off switch as per the values indicated in the chapter
"Electrical characteristics., which is to be located in an area which is
compliant with safety instructions and which cannot be reached by
the users who are using the spa.
instruction. Any other procedure is prohibited.
I
The installation of electrical devices and equipment (sockets,
switches, etc.) near the spa must be in compliance with legal
standards and regulations in the country where the spa is
installed.
I
The disconnection devices must be installed in the power
supply network according to the installation instructions.
I
For the equipotential connection as required by specific
national standards, the installer must use the terminal provided
(standard EN 60335.2.60) in the electrical box, and marked
It is mandatory to comply with this
with the symbol
In particular, an equipotential condition must
.
be established for all metallic masses surrounding the spa, for
example water and gas pipes, metallic platforms, and so on.
Refer to the pre-installation information sheet for in-
structions and electrical input of the various models.

Start-up instructions

Read each step in its entirety before proceeding with
that step.
I
Remove any dirt from the spa. Although the spa shell has been pol-
ished at the factory, you may want to treat it with a specially formulated s-
pa cleaner and wax available from your dealer prior to filling the first time.
I
Filling the spa
Remove the filter cover and the filter cartridge as indicated in
the chapter on cleaning the filter.
Position the end of the hose inside the filter connection and fill
the spa until the level of water covers all of the nozzles, without
however reaching the headrest.
Do not overfill your mini-pool.
N.B.: If your water is extremely hard, it is preferable to fill
halfway with hard water and the rest of the way with softened
water.
Always fill the mini-pool from the filter fitting so as to expel air
trapped in the pump intake. Otherwise, the air may remain in the
nozzle of pump, preventing the pump from circulating the water.
After filling, make sure the filter is installed properly before ap-
plying power to the mini-pool (refer to the chapter on cleaning
the filter).
I
Checks
Open the cabinet access panel and check all pump fittings to
make sure they are tight. Loosening can occur during shipping
and handling.
I
Turning on power
Turn on power to spa at the home's circuit breaker: the heater and
pump automatically activate. The water temperature LED flash on
the control panel and the messages "COL" or "ICE" appear.
NOTE: "COL" and "ICE" will only appear when the spa is in
Economy mode.
I
Start-up
Activating the pump(s)
I
Addition of chemical additives at first start-up
Please refer to the Jacuzzi system water treatment guide and rel-
ative catalogue for details on water quality maintenance, the
methods and warnings governing the use of relative chemical
products.
N.B.: Always cover the spa (except when mixing chemical
additives!) with the insulating cover, so as to reduce heating
times and thus minimize operating costs.
21

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

J-210J-235J-245J-275

Inhaltsverzeichnis