Electrical Safety; Start-Up Instructions - Jacuzzi MAXI-PREMIUM J-460 Montageanweisung, Bedienung Und Wartung

Electrical safety

®
The MaxiJacuzzi are safe products, manufactured in compliance with
standards EN60335-2-60: 1997, EN60335-1: 1994+A1+A2+A11-
A16, EN60825-1: 1994+A1+A2; EN55014-2 (1997), EN61000-3-2
(2000), EN61000-3-3 (1995 W/A1:01), EN61000-4-3 (2002
W/A1:02), EN61000-4-11 (2004), CISPER 22 (1997) Class B, FCC
Part 15 Subpart B Class B, VCCI (April 2000) Class B & ICES_003
Class B (ANSI C63.4 2003) TUV Test plan 02173520.024,
EN55022 Class B (1998), EN50082-1 (1997), ETSI EN 300 220-1
V2.1.1 (2006-04), ETSI EN 301-489-3 V1.4.1 (2002-08)
during production to ensure user safety.
I
Installation must be performed by qualified personnel who
ensure compliance with current national regulations and who
are also authorized to issue a certificate of compliance with
proper installation procedures.
It is the responsibility of the installer to select ma-
terials based on their intended use, to carry out
work properly, to check the condtion of the system
that the unit will be connected to and that it en-
sures safety of use also concerning maintenance
work and the possibility to examine the system.
I
The MaxiJacuzzi
must be permanently connected, without any intermediate
connections, to the electrical system and to the protection
system (earth system).
The electrical system of the building must be pro-
vided with a 0.03A differential switch and with an
efficient protection (earth) circuit.
Check for proper operation of the differential switch
by pressing the TEST button, which should trip.
I
For connection to the electrical mains, it is necessary to install
an omnipolar cut-off switch as per the values indicated in the
chapter "Electrical characteristics., which is to be located in an
area which is compliant with safety instructions and which can-
not be reached by the users who are using the MaxiJacuzzi
It is mandatory to comply with this instruction. Any other proce-
dure is prohibited.
I
The installation of electrical devices and equipment (sockets,
switches, etc.) near the MaxiJacuzzi
with legal standards and regulations in the country where the
®
MaxiJacuzzi is installed.
I
The omnipolar switches which were previosuly mentioned
must ensure an opening of contacts of at least 3 mm, and they
must be compliant with the voltage and current as specified in
the chapter "Technical characteristics".
I
For the equipotential connection as required by specific
national standards, the installer must use the terminal provided
(standard EN 60335.2.60) in the electrical box, and marked
with the symbol
be established for all metallic masses surrounding the spa, for
example water and gas pipes, metallic platforms, and so on.
Downloaded from www.Manualslib.com
®
are class "I" appliances and therefore they
®
must be in compliance
In particular, an equipotential condition must
.
manuals search engine
Refer to the pre-installation information sheet for in-
structions and electrical input of the various models.

Start-Up Instructions

Read each step in its entirety before proceeding with
that step.
I
Remove any dirt from the spa. Although the spa shell has been
and tested polished at the factory, you may want to treat it with a specially
formulated spa cleaner and wax available from your dealer prior to
filling the first time.
I
Filling the Spa
Remove the filter cover, then remove both filter cartridges as out-
lined in section "Cleaning The Filters".
Place the end of your garden hose into empty skimming filter
bucket (filter bucket on your left) as you stand next to the spa.
Fill spa half way, then place the garden hose into the opposite
filter bucket (filter bucket on your right) while adding the re-
maining fill water.
Fill spa until water level is above all jets and just touching the
bottom of each headrest in its lowest position.
Do not overfill your mini-pool.
N.B.: If your water is extremely hard, it is preferable to fill
halfway with hard water and the rest of the way with softened
water. Or, you may fill entirely with hard water if you use a spe-
cial water additive.
Always fill the spa from both filter connections, so as to expel
air trapped in the pumps. Otherwise the air may remain trapped,
preventing the pumps from circulating the water.
After filling, make sure both filters are installed properly before
applying power to the spa. (refer to sec. "Cleaning The Filters").
I
Checks
Open the cabinet access panel and check all pump fittings to
®
.
make sure they are tight. Loosening can occur during shipping
and handling.
I
Turn on Power
Turn on power to spa from the main switch (refer to the chap-
ter "Electrical safety". The heater and circulation pump will au-
tomatically activate.
If the control panel LCD flashes water temperature and "COOL"
or "ICE", refer to "Troubleshooting-Display messages".
I
Startup
Press once on the keys JETS 1 and 2 on the control panel.
I
Addition of chemcial additives at first start-up
Add the spa water chemicals as recommended by your dealer (refer
to the chapter "Water Quality Maintenance" for general guidance).
N.B.: Always cover the spa (except when mixing chemical
additives!) with the insulating cover, so as to reduce heating
times and thus minimize operating costs.
31