Electrical Safety - Jacuzzi VIRGINIA experience Vorinstallationsblatt

We recommend that you avoid bends, as far as possible, (we sug-
gest you use flexible PVC hoses).
In the instance where the main spa-pak has a heat exchanger for
heating water, it is necessary to connect the primary circuit to the
system which supplies hot water, in addition to connecting the elec-
trical box with devices (solenoid valve, motor pump) that control the
recirculation of the hot water in the exchanger's primary circuit.
Water connections for the Spa-Pak must also include the con-
nection between the filter and a ground drainage point.
Spa-Pak must always be installed in a ventilated indoor
area, which is not accessible to persons without a key or
tools and it must be protected from water and bad
weather (see note "Spa-Pak and the balance tank" in the pre-
vious chapter).
For perfect operation of the system, the Spa-Pak must be
installed at the same level as the balance tank (
or with a minimal difference.
I
The balance tank
When possible, it must be installed near the Hot tub for optimum
efficiency (excess water will fall into the balance tank). For cor-
rect operation of the balance tank, comply
dimensions provided in the respective tables
If the balance tank is installed outside, a suitable system
must be provided to protect it against the sun's rays and
ultraviolet radiation, to prevent damaging the container.

Electrical safety

The spas of the Experience range are safe products, manufactured in
compliance with standards EN 60335.2.60, EN 61000, EN 55014
and tested during production to ensure their safety.
I
Installation must be carried out by qualified and authorized per-
sonnel, in compliance with the national provisions in force.
It is the responsibility of the installer to choose the
materials in relation to their use, to carry the work out
correctly, to check the condition of the system to
which the appliance is to be connected and its suit-
ability and to guarantee safety when in use, regard-
ing maintenance operations and inspection of the
system.
I
The spas of the Experience range are class "1" appliances and
therefore they must be permanently connected, without any
intermediate connections, to the electrical system and to the
protection system (earth system).
The appliance must be powered by a differential cir-
cuit breaker; the operating current must not exceed
30mA.
Check that the differential switch is working correctly
by pressing the test button (TEST), which must click.
I
For connection to the mains, it is necessary to install a discon-
necting multiple-pole switch that provides full disconnection under
overvoltage category III conditions (
a place that complies with safety regulations and, in any case, which
cannot be reached by those using the spa.
Compliance with this regulation is obligatory: any other procedure is
prohibited.
If the building's electrical system is not able to gua-
rantee a stabile power supply, it is recommended
to install a voltage stabiliser that suitably dimen-
sioned for the required power upstream of the e-
i
6, detail 2) quipment.
I
The disconnection devices must be installed in the power supply
network according to the installation instructions.
I
with the The installation of electrical devices and equipment (sockets,
i
( 6). switches, etc.) near the spa must be in compliance with legal stan-
dards and regulations in the country where the spa is installed.
I
For the purpose of equipotential connection in compliance with
specific national regulations, the installer must use the provided
terminal (EN 60335.2.60 standards) on the electric wiring box
i
( 4), and marked by the symbol
In particular, equipotential connection must be carried out for all
metal parts surrounding the mini-pool, for example, the water and
gas pipes and any surrounding metal under-frames etc.
I
The appliance comes equipped with an LED lighting system, in
compliance with Regulation EN 62471:2009.
19
Parts incorporating electrical components,
except remote control devices, must be located
or fixed so that they cannot fall into the spa.
Live components and equipment must be out of
reach of individuals in the spa.
i
CAUTION! Before carrying out any maintenance
operation, disconnect the appliance from the pow-
er supply line.
3-4). It must be positioned in
.