Jacuzzi J-200 series Montageanweisung Und Bedienung Und Wartung Seite 33

Press either of these buttons to change music folders
1
(Device Mode USB)
Preset 1: Press to access a preset station (Radio Mode)
2
Preset 2: Press to access a preset station (Radio Mode)
Press once to repeat the song. Press again to repeat the
3
album (Device Mode USB)
Preset 3: Press to access a preset station (Radio Mode)
Press to play songs in a random order (Device Mode USB)
Not used (Radio Mode)
Electronic Device Connections and Functions
CAUTION: RISK OF ELECTRICAL SHOCK OR E-
QUIPMENT DAMAGE! Never install, remove or operate
any electrical device (e.g. iPod/MP3/USB/AUX/Bluetooth)
while hands are wet or while sitting partially or fully immer-
sed in the spa!
Operating the Radio:
Turn power ON to the stereo unit and remote.
The LCD screen on the remote will display the following: "Wel-
come, " "Load, " "Radio" and the station number.
You can use the seek button to search for frequencies. You can
save up to 3 stations as presets.
Follow the steps below to set a station:
a. Find a station you want to save.
b. Press and hold one of the three preset buttons. The station
number on the display will quickly flash to confirm the setting.
To set the additional two stations, conduct this step again.
Connecting Your iPod®/MP3 Player Using the USB:
- Turn power OFF to the stereo unit.
- Locate the USB port in the stereo locker.
- Locate the 30-pin cable provided for compatible devices or a
cable provided with your device.
- Connect the USB end of the cable into the USB connection
on stereo.
- Connect the 30-pin end of the cable to the iPod/MP3 Player
(purchased separately).
- After connecting the cable to both devices, set the player in-
to the rubber holding base.
USB USB
AUX AUX
Operating iPod/MP3 Player
- Turn power ON to the stereo unit, the player and the stereo re-
mote.
- The LCD screen on the remote will display the following: "Wel-
come, " "USB, " "Load, " "Apple" (final display will vary depending
on the device connected). All functions are performed throu-
gh the remote.
- While the music is playing the remote screen will display and-
continually scroll through the following: Artist, Album, Song
and Track information.
- For operational functions refer to the "External Media Device
Playback" section.
Operating the USB drive:
- Turn power OFF to the stereo unit.
- Plug in your USB device into the "USB" connection on the ste-
reo.
- Turn power ON to the stereo unit and the stereo remote.
- The LCD screen on the remote will display the following: "Wel-
come, " "USB, " "Load, " "TOL XX" (final display will vary depen-
ding on the whether the USB holds folders or files). All func-
tions are performed through the remote.
- While the music is playing the remote screen will display and-
continually scroll through the following: Title, Song, Artist, Al-
bum, Dir, Music and Track information.
- For operational functions refer to the "External Media Device
Playback" section.
Connecting Your Auxiliary Player Using the 3.5 mm Cable:
- Plug one end of the cable to "Aux" connection on the stereo.
- Plug the other end of the supplied cable into the phone jack
connection on the iPod/MP3 Player.
- All playback operations are conducted via the Auxiliary Player.
The stereo remote functions do not work on the external Auxi-
liary Player (except volume control).
Connecting Your Bluetooth Device:
- Turn power ON to the stereo unit.
USB
AUX
- From your Bluetooth device, make sure the Bluetooth feature
is ON.
- Follow the pairing instructions for your Bluetooth device and
connect to the "BLUEWAVE" device that appears on your
screen.
- When asked for a password, enter the code "0000. "
- The remote LCD screen will display, "BT CONNECTED" if the
process was successful.
33
USB USB
AUX AUX