Additional Safety Instructions - Scheppach HM80L Original Bedienungsanleitung

Keep the handle dry, clean and free of oil and
–
grease.
Pull the plug out of the outlet
15
Never remove loose splinters, chips or jammed
–
wood pieces from the running saw blade.
– During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
Do not leave a tool key inserted
16
Before switching on, make sure that keys and
–
adjusting tools are removed.
Avoid inadvertent starting
17
– Make sure that the switch is switched off when
plugging the plug into an outlet.
Use extension cables for outdoors
18
Only use approved and appropriately identified
–
extension cables for use outdoors.
Only use cable reels in the unrolled state.
–
19 Remain attentive
– Pay attention to what you are doing. Remain
sensible when working. Do not use the electric
tool when you are distracted.
Check the electric tool for potential damage
20
Protective devices and other parts must be care-
–
fully inspected to ensure that they are fault-free
and function as intended prior to continued use
of the electric tool.
Check whether the moving parts function fault-
–
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-
free operation of the electric tool.
– The moving protective hood may not be fixed in
the open position.
Damaged protective devices and parts must be
–
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
fied in the operating manual.
– Damaged switches must be replaced at a cus-
tomer service workshop.
Do not use any faulty or damaged connection
–
cables.
Do not use any electric tool on which the switch
–
cannot be switched on and off.
ATTENTION!
21
– Exercise elevated caution for double mitre cuts.
22 ATTENTION!
The use of other insertion tools and other ac-
–
cessories can entail a risk of injury.
Have your electric tool repaired by a qualified
23
electrician
This electric tool conforms to the applicable
–
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

Additional safety instructions

Safety precautions
1
Warning! Do not use damaged or deformed
–
saw blades.
– Replace a worn table insert.
Only use saw blades recommended by the
–
manufacturer which conform to EN 847-1.
Make sure that a suitable saw blade for the
–
material to be cut is selected.
Wear suitable personal protective equipment.
–
This includes:
– Hearing protection to avoid the risk of be-
coming hearing impaired,
Respiratory protection to avoid the risk of
–
inhaling harmful dust,
Wear gloves when handling saw blades and
–
rough materials. Carry saw blades in a con-
tainer whenever practical.
– Wear goggles. Sparks generated during
work or splinters, chippings and dust coming
from the device can lead to loss of eyesight.
Connect a dust collecting device to the electric
–
tool when sawing wood. The emission of dust
is influenced, among other things, by the type
of material to be processed, the significance of
local separation (collection or source) and the
correct setting of the hood/guide plates/guides.
Do not use saw blades made of high-speed
–
alloy steel (HSS steel).
Maintenance and repair
2
– Pull out the mains plug for any adjustment or
repair tasks.
The generation of noise is influenced by various
–
factors, including the characteristics of saw blades,
condition of saw blade and electric tool. Use saw
blades which were designed for reduced noise
development, insofar as possible. Maintain the
electric tool and tool attachments regularly and if
necessary, initiate repairs in order to reduce noise.
Report faults on the electric tool, protective de-
–
vices or the tool attachment to the person respon-
sible for safety as soon as they are discovered.
Safe work
3
Only use saw blades for which the maximum
–
permissible speed is not lower than the maxi-
mum spindle speed of table saws and which
are suitable for the material to be cut.
Make sure that the saw blade does not touch
–
the rotary table in any position by pulling out
the mains plug and rotating the saw blade by
hand in the 45° and 90° position. If necessary,
readjust the saw head.
When transporting the electric tool, only use
–
the transport devices. Never use the protective
devices for handling or transport.
– Make sure that the lower part of the saw blade
is covered during transport, e.g. by the protec-
tive device.
GB 23