Settings; Working Instructions - Scheppach HM80L Original Bedienungsanleitung

11. Settings

CROSS-CUTTING
ATTENTION: Before carrying out the following ad-
justments, please check whether the motor of the
machine is switched off.
Pivoting the table plate (Fig. 2)
The mitre saw can be pivoted left and right with the
rotary table. Exact angle adjustment is possible on
the basis of the scale. The angle can be precisely and
quickly adjusted from 0° to 45° with locking positions
at 15°, 22.5° and 30°.
To pivot the rotary table, loosen the set screw (21)
and rotate the unit using the handle (20) until the de-
sired angle is reached. Then secure it with the set
screw (21).
Tilt of the saw unit (Fig. 3)
The saw unit can be tilted at an angle of up to 45°.
Loosen the handle (23) on the rear side of the ma-
chine and tilt the unit to the desired angle position
according to the scale. The angle can be set on the
basis of the scale (24) using the pointer (25). Then
the handle must be re-tightened.

12. Working instructions

After you have carried out all the tasks described
above, you can begin working.
ATTENTION: Always keep your hands away from
the cutting zone and never attempt to reach in while
cutting.
FIXING A WORKPIECE
Clamp the work piece on the work table with the
workpiece clamp (10 - Fig 1) in order to fix it in place.
Cross cut 90° and turntable 0° (Fig. 4, 1.3)
Attention! For 90° mitre cuts, the moveable stop rail
(27a) must be fixed in the inner position.
• Open the set screw (27b) on the moveable stop
rail (27a) with an Allen key and push the moveable
stop rail (27a) inwards.
• The moveable stop rail (27a) must be locked in a
position far enough from the inner position that the
distance between the stop rail (27a) and the saw
blade (5) is no more than 8 mm.
• Before making the cut, check that no collision
could occur between the stop rail (27a) and the
saw blade (5).
• Secure the locking lever (27b) again.
• Loosen the locking knob (26).
• Lift the saw unit by the handle (2) until it locks in
place in the top position.
• Lock the material with the clamping device (10)
on the fixed saw table to prevent the material from
moving during the cutting operation.
• Press the workpiece evenly on the stop strips (27);
make sure that you hand remains outside the cut-
ting area of the saw blade.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
• With your right hand on the handle (2), press the
locking lever (3) so that the unit can also be pivoted
downward.
• The motor starts when the start button (1) is
pressed.
• Slowly bring the saw blade down to the workpiece
and cut through it with moderate pressure.
• When the cutting operation is completed, move
the machine head back to its upper (home)
position and release the ON/OFF button (1).
Attention! The machine executes an upward
stroke automatically due to the return spring, i.e.
do not release the handle (2) after completing the
cut; instead allow the machine head to move up-
wards slowly whilst applying light counter pressure.
Cross cut 90° and turntable 0° - 45° (Fig. 4, 2, 1.3)
The crosscut saw can be used to make crosscuts of
0°-45° to the left and 0° -45° to the right in relation
to the stop rail.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (27a) must be fixed in the inner
position.
Open the set screw (27b) on the moveable stop rail
•
(27a) and push the moveable stop rail (27a) out-
wards.
• The moveable stop rail (27a) must be locked in a
position far enough from the inner position that the
distance between the stop rail (27a) and the saw
blade (5) is no more than 8 mm.
Before making the cut, check that no collision could
•
occur between the stop rail (27a) and the saw blade
(5).
• Tighten the set screw (27b) again.
Loosen set screw (21).
•
Use the handle (2) to set the turntable (9) to the de-
•
sired angle. The pointer on the turntable must co-
incide with the desired angular extent of the scale
on the base (7).
• Re-tighten the locking screw (21) to fix the turntable
(9).
Cut as described under section „Cross cut 90° and
•
turntable 0°".
Mitre cut 0°- 45° (Fig. 1, 1.3)
The crosscut saw can be used to make mitre cuts of
0° - 45° in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (27a) must be fixed at the
outer position.
• Open the set screw (27b) for the adjustable stop
rail (27a) with an Allen key and push the adjustable
stop rail outwards.
• The adjustable stop rail (27a) must be fixed far
enough in front of the innermost position that the
distance between the stop rail (27a) and the saw
blade (5) amounts to a maximum of 8 mm.
• Before making a cut, check that the stop rail (27a)
and the saw blade (5) cannot collide.
• Secure the locking lever (27b) again.
• Move the machine head to the top position.
GB 27