Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• Use extra care when cutting material with irregular
cutting profiles.
• When withdrawing the workpiece, teeth can get
caught in the kerf, especially if the shavings block
the kerf. In this case you should switch off the saw,
pull out the mains plug, open the kerf with a wedge
and remove the workpiece.
• Never leave the work station without setting down
the saw beforehand. Wait until the saw has come
to a standstill.
• Do not place, glue, or assemble any parts on the
work table while the saw is running.
• Do not switch on the saw until the work table is
cleared of material residues and tools. Only leave
the workpiece to be machined and any work aids
(wedges) on the workbench.
• Always wear eye protection.
• Keep fingers at a safe distance from the saw blade.
• Guide the workpiece securely and firmly and do not
let it loose at any point.
• Never leave the work station without setting down
the saw beforehand.
• Do not let your familiarity with the saw lead you to
carelessness. Carelessness can lead to serious in-
juries in a split second.
Keep these safety instructions in a safe place.
5.3 Safety instructions for handling batteries
1.
Always make sure that the batteries are inserted
with the correct polarity (+ and –), as indicated on
the battery.
2.
Do not short-circuit batteries.
3.
Do not charge non-rechargeable batteries.
4.
Do not overcharge batteries!
5.
Do not mix old and new batteries or batteries of dif-
ferent types or manufacturers! Replace an entire
set of batteries at the same time.
6.
Immediately remove used batteries from the de-
vice and dispose of them properly! Do not throw
batteries away with household waste. Defective
or used batteries must be recycled according to
Directive 2006/66/EC.
Return batteries and / or the device to the collec-
tion facilities offered. Contact your local authority
or city administration for information about dispos-
al options.
7.
Do not allow batteries to heat up!
8.
Do not weld or solder directly on batteries!
9.
Do not dismantle batteries!
10. Do not allow batteries to deform!
32 | GB
11. Do not throw batteries into fire!
12. Keep batteries out of the reach of children.
13. Do not allow children to replace batteries without
supervision!
14. Do not keep batteries near fire, ovens or other
sources of heat. Do not use batteries in direct sun-
light or store them in vehicles in hot weather.
15. Keep unused batteries in the original packaging
and keep them away from metal objects. Do not
mix unpacked batteries or toss them together! This
can lead to a short-circuit of the battery and thus
damage, burns or even the risk of fire.
16. Remove batteries from the equipment when it will
not be used for an extended period of time, unless
it is for emergencies!
17. NEVER handle batteries that have leaked without
appropriate protection. If the leaked fluid comes
into contact with your skin, the skin in this area
should be rinsed off under running water imme-
diately. Always prevent the fluid from coming into
contact with the eyes and mouth. In the event of
contact, please seek immediate medical attention.
18. Clean the battery contacts and corresponding con-
tacts in the device prior to inserting the batteries.
6. Technical data
Mains voltage
Power consumption
Stroke rate
Lifting movement
Dimensions L x W x H
Tilting table
Table size
Saw blade length approx.
(between both pins)
Saw arm swing
Cutting height max. at 90°
Cutting height max. at 45°
Protection category
Suction port ø
Weight
*Operating mode S1 (continuous operation)
www.scheppach.com
230-240 V~/50 Hz
70 W (S1*)
90 W (S2 15min**)
550-1500 rpm
18 mm
665 x 310 x 340 mm
0° to 45° to the left/
right
254 x 407 mm
127 mm
405 mm
50 mm
20 mm
IP20
34.5 mm
8.1 kg
Werbung
Inhaltsverzeichnis
Fehlerbehebung
