Scheppach HM80L Original Bedienungsanleitung Seite 24

Be sure to only use spacers and spindle rings
–
specified by the manufacturer as suitable for
the intended purpose.
The floor around the machine must be level,
–
clean and free of loose particles, such as chips
and cutting residues.
Do not remove any cutting residues or other parts
–
of workpieces from the cutting zone while the
machine is running and the saw unit is not at rest.
Make sure that the machine is always secured
–
on a workbench or a table if at all possible.
Support long workpieces (e.g. with a roller ta-
–
ble) to prevent them sagging at the end of a cut.
Make sure you select the appropriate saw blade
–
for the material you are cutting.
Warning! Never use the saw for cutting material
other than that specified by the manufacturer.
Use the saw only when the protective devices
–
are functional, they are in good condition and
in the proper position.
Ensure that the rotation speed indicated on the
–
saw blade is the same as the rotation speed
indicated on the saw.
The workpiece must always be clamped at the
–
saw table.
– Before each cutting operation make sure that
the machine is safe.
–
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
SAFETY INSTRUCTIONS FOR THE HANDLING
OF SAW BLADES
1 Only use insertion tools if you have mastered
their use.
Observe the maximum speed. The maximum
2
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
3 Observe the motor / saw blade direction of rotation.
4 Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
Clean grease, oil and water off of the clamping
5
surfaces.
Do not use any loose reducing rings or bushes
6
for the reducing of holes on saw blades.
7 Make sure that fixed reducer rings for securing
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
Make sure that fixed reducer rings are parallel
8
to each other.
Handle insertion tool with caution. They are ide-
9
ally stored in the originally package or special
containers. Wear protective gloves in order to im-
prove grip and to further reduce the risk of injury.
24 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
10 Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
Prior to use, make sure that the insertion tool
11
meets the technical requirements of this electric
tool and is properly fastened.
12 Only use the supplied saw blade for cutting wood,
never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from ac-
cidents using suitable precautionary measures!
• Do not look directly into the laser beam with un-
protected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representa-
tive.
Safety instructions for handling batteries
1 Always make sure that the batteries are inserted
with the correct polarity (+ and –), as indicated
on the battery.
Do not short-circuit batteries.
2
Do not charge non-rechargeable batteries.
3
Do not overcharge batteries!
4
5 Do not mix old and new batteries or batteries
of different types or manufacturers! Replace an
entire set of batteries at the same time.
Immediately remove used batteries from the de-
6
vice and dispose of them properly! Do not dis-
pose batteries with household waste. Defective
or used batteries must be recycled according to
Directive 2006/66 / EC. Give back batteries and
/ or the device has been offered to the collective
facilities. About disposal facilities you can inform
by your municipal or city government.
Do not allow batteries to heat up!
7
Do not weld or solder directly on batteries!
8
9 Do not dismantle batteries!
10 Do not allow batteries to deform!
11 Do not throw batteries into fire!