Denon AVR- 1603 Bedienungsanleitung Seite 16

1 2 5
o °e_e°°
o 8v
ooo
3
Select the input source to be played
Example: CD
IMain unit} IRemate control unit}
2
Select the input mode
• Selecting the analog mode
Press the ANALOG button to switch to the
analog input
% %
(Main unit} IRemote control unit}
• Selecting the external input {EXT IN) mode
Press the EXT IN {or the EXT IN button on
the remote control unit) to switch the external
_nput
_.IN
% %
(Main unit} IRemote control unit}
• Selecting the AUTO, PCM and DTS modes
The mode switches as shown below each time
the INPUT MODE button is pressed
AUTO _ PCM _DTS
f
% %
(Main unit} IRemote control unit}
Input mode selection function
Different input modes can be selected for the different
input sources¸ The selected input modes for the
separate input sources are stored in the memory¸
@)AUTO (All auto mode}
In this mode, the types of signals being input to the
digital and analog input jacks for the selected input
source are detected and the program in the AVR-
1603's surround decoder is selected automatically
16
3
1
2
upon playback TMs mode can be selected for all
input sources other than TUNER
The presence or absence of digital signals is
detected, the signals input to the digital input iacks
are identified and decoding and playback are
performed automatically in DTS, Dolby Digital or
PCM (2 channel stereo} format If no digital signal
is being input, the analog input jacks are selected
Use this mode to play Dolby Digital signals
PCM (exclusive PCM signal playback mode)
Decoding and playback are only per[ormed when
PCM signals are being input
Note that noise may be generated when using this
mode to play signals other than PCM signals
DTS (exclusive DTS signal playback mode)
Decoding and playback are only per[ormed when
DTS signals are being input
_ANALOG (exclusive analog audio signal playback
mode)
The signals input to the analog input iacks are
decoded and played
EXT IN (external decoder input jack selection mode}
The signals being input to the external decoder
input jacks are played without passing through the
surround circuitry
NOTE:
• Note that noise will be output when CDs or LDs
recorded in DTS format are played in the "PCM"
(exclusive PCM signal playback) or "ANALOG"
(exclusive analog audio signal playback) mode
Select the AUTO or DTS (exclusive DTS signal
playback] mode when playing signals recorded in
DTS from a laser disc player
Notes on playing a source encoded with DTS
• Noise may be generated at the beginning of
playback and while searching during DTS
playback in the AUTO mode. If so, play in the
DTS mode.
• In some rare cases the noise may be generated
when you preform the operation to stop
playback of a DTS-CD or DTS-LD,
Selectthe play mode
Press the SURROUND MODE button, then turn
the SELECT knob
Example: Stereo
su_14coe s_eo
(Main unit} (Remote control unit}
To select the surround mode _
while adiusting the surround
parameters, channel volume or
tone control, press the surround
mode button then operate the (Mainunt)
selector (See page 18)
4 Start playback on the selected component
• For operating instructions, refer to the compenent's
manual
Adjust the volume
The vol_rr e level is
disp r_yed on _e mas%e
voume _evel d splay {Main unit) _Remote control unit}
The volume can be adiusted within the range
ot -70 to 0 to 18 dB, in steps of 1 dB However,
when the channel level is set as described on
page 18, if the volume for any channel is set
at +1 dB or greater, the volume cannot be
adjusted up to 18 dB (In this case the
maximum volume is adiusted to "18 dB --
(Maximum value of channel levell" )
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs
are played in the "ANALOG" or "PCM" mode
When playing DTS-compatible sources, be sure to
connect the source component to the digital input
iacks {OPTICAL/COAXIAL) and set the input mode
to "DTS"
[t] Adjusting the sound quality (tone}
The tone switches as follows each time the TONE
CONTROL button is pressed
BASS _ TREBLE
(Ma_n unit)
Input mode display
• In the AUTO mode
One of these I_gh{s depending
on _he input s_gnal
• In the DIGITAL PCM mode
• In the DIGITAL DTS mode
• In the ANALOG mode
o o
Input signal display
• DOLBY DIGITAL
• DTS
o ,.
• PCM
The _ indicator lights when digital signals
are being input properly If the _ indicator
does not light, check whether the digital input
component setup {page I2) and connections are
correct and whether the component's power is
turned on
NOTE:
• The _ indicator will light when playing
CD-ROMs containing data other than audio signals,
but no sound will be heard
1
m o • -
3 21