Scope Of Delivery; Declaration Of Conformity; Additional Accessories - Bosch MS 200 Installationsanleitung

• If the temperature in the DHW cylinder is less than the required DHW
temperature by the set switch-on temperature differential, the DHW
cylinder is heated up.
Basic primary store system for heating a buffer cylinder for heat
interface units
• If the temperature in the buffer cylinder is less than required in the set
switch-on temperature differential, the buffer cylinder will be heated
up.
• Therm.dis./daily ht cyl1 must be deactivated.
This system is only available with the CR 400/CW 400/CW 800/RC300/
RC310 user interface and is configured via the DHW settings. A DHW
circulation pump can be connected.
2.6

Scope of delivery

Fig. 1 at end of document:
[1] Module
[2] Cylinder temperature sensor (TS2)
[3] Collector temperature sensor (TS1)
[4] Bag with strain relief
[5] Installation instructions
2.7

Declaration of Conformity

The design and operating characteristics of this product comply with the
European and national requirements.
The CE marking declares that the product complies with all the
applicable EU legislation, which is stipulated by attaching this
marking.
The complete text of the Declaration of Conformity is available on the
Internet: www.bosch-thermotechnology.com.
2.8 Specifications
Specifications
Dimensions (W × H × D)
Maximum conductor cross-section
• 230 V terminal
• Extra-low voltage terminal
Rated voltages
• BUS
• Module mains voltage
• HMI
• Pumps and mixers
Fuse
BUS interface
Power consumption on – standby
Maximum output
Maximum output per connection
• PS1; PS4; PS5; VS1/PS2/PS3
• VS2
MS 200 – 6720879925 (2017/11)
0010015813-001
246 × 184 × 61 mm (further
dimensions  Illustration 2 at
the end of this document)
2
• 2.5 mm
2
• 1.5 mm
• 15 V DC (reverse-polarity-
protected)
• 230 V AC, 50 Hz
• 15 V DC (reverse-polarity-
protected)
• 230 V AC, 50 Hz
230 V, 5 AT
EMS 2/EMS plus
< 1 W
1100 W
• 400 W (high-efficiency
pumps permissible;
<30 A for 10 ms)
• 10 W
Specifications
Cylinder temperature sensor
measuring range
• Lower fault limit
• Display area
• Upper fault limit
Capturing range, collector
temperature sensor
• Lower fault limit
• Display area
• Upper fault limit
Permitted ambient temp.
Protection
Protection class
ID no.
Table 2
 
°C °C
20 14772 45 5523
25 12000 50 4608
30 9786 55 3856
35 8047 60 3243
40 6653 65 2744
Table 3 Temperature sensor measurements (TS2 - TS6, TS8 - TS20)
 
°C °C
– 30 364900 25 20000
– 20 198400 30 16090
– 10 112400 35 12800
0 66050 40 10610
5 50000 50 7166
10 40030 60 4943
15 32000 70 3478
20 25030 75 2900
Table 4 Measurements, collector temperature sensor (TS1 / TS7)
2.9

Additional accessories

For precise information regarding suitable accessories, refer to
manufactures website.
• For solar thermal system 1:
– Solar pump; connection to PS1
– electronically regulated pump (pulse width modulation or or
0-10 V); connection to PS1 and OS1
– Temperature sensor (1st collector array); connection to TS1
(Scope of delivery)
– Temperature sensor at the bottom of the 1st cylinder; connection
to TS2 (scope of delivery)
• Additionally for central heating backup (A) (
– 3-way valve; connection to VS1/PS2/PS3
– Temperature sensor in the middle of the 1st cylinder; connected
to TS3
– Temperature sensor situated at the return; connection to TS4
• Additionally for 2nd cylinder/swimming pool with valve (B):
– 3-way valve; connection to VS2
– Temperature sensor at the 2nd cylinder, at the bottom;
connection to TS5
Product information
• < – 10 °C
• 0 ... 100 °C
• > 125 °C
• < – 35 °C
• – 30 ... 200 °C
• > 230 °C
0 ... 60 °C
IP 44
I
Data plate ( Fig. 19 at the
end of document)
 
°C °C
70 2332 95 1093
75 1990 100 950
80 1704 – –
85 1464 – –
90 1262 – –
 
°C °C
80 2492 150 364
90 1816 160 290
95 1500 170 233
100 1344 180 189
110 1009 190 155
120 768 200 127
130 592 – –
140 461 – –
):
25