Use And Maintenance - Baron SERIE 700 Aufstellung, Gebrauchs- Und Instandhaltungs Anweisungen

Data Emissione 27/06/2003
4 - CHECK OF SOME MALFUNCTIONS
Some malfunctions can occur during the normal operation of the
equipment:
4.1 Heating is not enabled
- The temperature control thermostat is faulty.
- Intervention of the safety thermostat.
- There is no power supply.
- The resistors are faulty.
4.2 Heating is not sufficient
- One or more elements of the heating resistor are faulty.
- A phase of the power supply is missing.
4.3 Intervention of the safety thermostat
- The operating thermostat is faulty.
- The water level is insufficient.
For the reset of the thermostat, refer to the paragraph 5.1.
5 - REPLACING SOME COMPONENTS
These operations must be carried out by authorized and qualified
professionals.
Before carrying out any repair and/or maintenance operation,
disconnect the power supply of the equipment turning off the
main switch installed before the range.
The sealed components must not be tampered with.
5-1 Operating and safety thermostats
Before enabling the safety thermostat again, eliminate the reasons
provoking the overheating: examine the functioning of the operating
thermostat, the resistors, etc... Then carry out the following
operations:
- Remove the control board.
- Press the red pushbutton of the thermostat.
- Check whether the electric circuit is closed.
Replace the safety and operating thermostats through the following
operations:
- Disconnect the main switch inserted before the equipment.
- Remove the control board.
- Extract the bulb from its own sheath applied inside the basin.
- Extract the knob and remove the screws fastening the component
to the control board.
- The switch and the operating thermostat are axially assembled
through the insertion of a proper connection flange: remove this
flange to release the two components.
- Replace the component and reassemble carrying out the same
operations backwards.
5.2 Heating resistors
- Disconnect the main switch inserted before the equipment.
- Open the door of the pasta cooker.
- Drain the water completely from the basin opening the drain cock
S (Fig. 1).
- Remove the control board.
- Disconnect the electric wiring from the terminals of the concerned
resistor.
- Unscrew the elements fastening the resistor to the basin.
- Now the resistor can be extracted from the basin.
- Replace the component and reassemble carrying out the same
operations backwards
- Close the drain cock and fill the basin checking that there is not
any leakage.
5.3 Main switch
- Remove the control board.
- Disconnect the wiring of this component.
- Extract the knob and remove the screws fastening the switch-
thermostat unit onto the control board.
- The switch and the thermostat are axially assembled through the
insertion of a proper connection flange: remove this flange to
release the two components.
- Replace the component and reassemble carrying out the same
operations backwards.
5.4 Warning lights
- Remove the control board.
- Disconnect the wiring of this component..
- Replace the component and reassemble carrying out the same
operations backwards.

6 - USE AND MAINTENANCE

6.1 Warning
This equipment has been designed for professional aims, therefore
it must be operated exclusively by trained personnel.
It must exclusively be used to cook food in pots and pans;
consequently any other use is improper.
Before switching on the cooker, clean all its surfaces in contact with
food, with the utmost care.
ATTENTION ! Never enable the heating system of this
equipment when its basin has no water.
Its installation and possible transformation for other supply voltages
(when possible) must be carried out only by authorized and qualified
installers.
In case of troubles, disconnect the main power switch, installed
before the equipment.
For any repair, call the authorized After-Sales Service and require
only original spare parts.
Not complying with these instructions may seriously
compromise the safety of this equipment; the manufacturer
declines any liability in case these warnings are not complied
with.
6.2 Safety devices
Any basin of pasta cookers is provided with a safety thermostat.
When the maximum control temperature is exceeded, the safety
thermostat disconnects the power supply. When this occurs, turn off
the main power switch and call an After-Sales Centre.
6.3 Use of the pasta cooker (Fig. 1)
Any basin of pasta cookers is equipped with a control knob M
(Fig.1) of the control thermostat/main switch, with a green LED
indicating "current on" and with a yellow LED indicating "heating
enabled".
The knob M of the control thermostat is marked with the following
symbols:
0 Heating off
40 Minimum temperature
70 Intermediate temperature values
100 Maximum temperature
12
Revisione 0.0