Intended Use; Safety Warnings - Makita LS1219 Betriebsanleitung

7R DYRLG LQMXU\ IURP À\LQJ GHEULV NHHS
holding the saw head down, after making
cuts, until the blade has come to a com-
plete stop.
:KHQ SHUIRUPLQJ VOLGH FXW ¿UVW SXOO FDU-
riage fully and press down handle, then
push carriage toward the guide fence.
'R QRW SODFH KDQG RU ¿QJHUV FORVH WR WKH
blade.
Never look into the laser beam. Direct laser
EHDP PD\ LQMXUH \RXU H\HV
Only for EU countries
Do not dispose of electric equipment
together with household waste material! In
observance of the European Directive, on
Waste Electric and Electronic Equipment
and its implementation in accordance with
national law, electric equipment that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.

Intended use

The tool is intended for accurate straight and miter
cutting in wood. With appropriate saw blades, aluminum
can also be sawed.
3RZHU VXSSO\
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
FDQ RQO\ EH RSHUDWHG RQ VLQJOHSKDVH $& VXSSO\ 7KH\
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
7KH W\SLFDO $ZHLJKWHG QRLVH OHYHO GHWHUPLQHG DFFRUG-
ing to EN62841:
Model LS1219
Sound pressure level (L
S$
Sound power level (L  G% $
:$
8QFHUWDLQW\ .  G% $
Model LS1219L
Sound pressure level (L
S$
Sound power level (L  G% $
:$
8QFHUWDLQW\ .  G% $
WARNING:
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Model LS1219
Vibration emission (a ) : 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
Model LS1219L
Vibration emission (a ) : 2.5 m/s
h
Uncertainty (K) : 1.5 m/s
 G% $
 G% $
2
or less
2
2
or less
2
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
(& 'HFODUDWLRQ RI &RQIRUPLW\
For European countries only
7KH (& GHFODUDWLRQ RI FRQIRUPLW\ LV LQFOXGHG DV $QQH[ $
to this instruction manual.

SAFETY WARNINGS

*HQHUDO SRZHU WRRO VDIHW\ ZDUQLQJV
WARNING:
WLRQV LOOXVWUDWLRQV DQG VSHFL¿FDWLRQV SURYLGHG
with this power tool. Failure to follow all instructions
OLVWHG EHORZ PD\ UHVXOW LQ HOHFWULF VKRFN ¿UH DQGRU
VHULRXV LQMXU\
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
6DIHW\ LQVWUXFWLRQV IRU PLWUH VDZV
1. Mitre saws are intended to cut wood or wood-
OLNH SURGXFWV WKH\ FDQQRW EH XVHG ZLWK DEUD-
sive cut-off wheels for cutting ferrous material
VXFK DV EDUV URGV VWXGV HWF $EUDVLYH GXVW
causes moving parts such as the lower guard to
MDP 6SDUNV IURP DEUDVLYH FXWWLQJ ZLOO EXUQ WKH
lower guard, the kerf insert and other plastic parts.
Use clamps to support the workpiece when-
2.
ever possible. If supporting the workpiece
E\ KDQG \RX PXVW DOZD\V NHHS \RXU KDQG DW
least 100 mm from either side of the saw blade.
Do not use this saw to cut pieces that are too
VPDOO WR EH VHFXUHO\ FODPSHG RU KHOG E\ KDQG
If your hand is placed too close to the saw blade,
WKHUH LV DQ LQFUHDVHG ULVN RI LQMXU\ IURP EODGH
contact.
16 ENGLISH
The vibration emission during actual
Be sure to identify safety measures
5HDG DOO VDIHW\ ZDUQLQJV LQVWUXF-