General Descriptions; Mig/Mag Convencional - Telwin MIG 215 AL Synergic Betriebsanleitung

INSTRUCTION MANUAL FOR WIRE WELDING MACHINE
IMPORTANT
READ THIS MANUAL AND THE SAFETY RULES
MANUAL CAREFULLY BEFORE INSTALLING, USING,
OR SERVICING THE WELDING MACHINE, PAYING
SPECIAL ATTENTION TO SAFETY RULES. CONTACT
YOUR DISTRIBUTOR
UNDERSTAND THESE INSTRUCTIONS.
It is essential to pay special attention to the "SAFETY
RULES" Manual. The symbols next to certain paragraphs
indicate points requiring extra attention, practical advice or
simple information.
This MANUAL and the "SAFETY RULES" MANUAL must
be stored carefully in a pica familiar to everyone involved in
using the machine. They must be consulted whenever
doubts arise and be kept for the entire lifespan of the
machine; they will also be used for ordering replacement
parts.
IN CASE OF MALFUNCTIONS, REQUEST ASSISTANCE
FROM QUALIFIED PERSONNEL.

1 GENERAL DESCRIPTIONS

1.1 SPECIFICATIONS
This welding machine is a power source made using
INVERTER technology, suitable for synergic pulsed
MIG/MAG welding,
conventional MIG/MAG. The equipment may be used only
for the purposes described in the manual. The equipment
must not be used to defrost pipes.
1.2 EXPLANATION OF TECHNICAL SPECIFICATIONS
The welding machine is manufactured
IEC 60974.1
according to these international standards
IEC 60974.10
Single-phase
frequency converter.
Flat characteristic
Suitable for continuous electrode (MIG/MAG)
welding.
Uo Secondary open-circuit voltage
X Duty cycle percentage.
The duty cycle expresses the percentage
of 10 minutes during which the machine
may run at a certain current without
overheating.
IF YOU DO NOT
non-pulsed synergic
static transformer-rectifier
I
2
U
2
U
1
1~ 50/60Hz
I Max
1
FULLY
I eff
1
IP23
NOTES: The welding machine has also been designed for
use in environments with pollution rating of 3. (See IEC
664).
1.3 PROTECTIONS
1.3.1 Block protection
In the event of a malfunction, a number with the following
meaning may appear on the display G:
52 = Start button pressed during start-up.
53 = start button pressed during thermostat reset.
56 = Extended
MIG/MAG, electrode and the material to be welded.
Shut the machine off and turn it back on.
If different numbers appear on the display, contact
technical service.
1.3.2 Mechanical protection (safety button)
When the movable side is opened, this activates the
safety button that prevents operation of the welding
machine. This protection, indicated when the LED A is lit,
avoids hazardous situations when the operator replaces
the roller of the wire feeder unit or the welding electrode.
1.3.3 Thermal protection
This machine is protected by a thermostat, which prevents
the machine from operating if the allowable temperatures
are exceeded.
running and the LED A lights.
2 INSTALLATION
Make sure that the supply voltage matches the voltage
indicated on the specification plate of the welding
machine.
Mounting a plug with an adequate capacity for the supply
cable, making sure that the yellow/green conductor is
connected to the earth pin.
The capacity of the overload cutout switch or fuses
installed in series with the power supply must be
equivalent to the absorbed current I
WARNING: This equipment does not comply with IEC
61000-3-12. If it is connected to a public low voltage
system, it is the responsibility of the installer or user of the
equipment to ensure, by consultation with the distribution
network operator if necessary, that the equipment may be
connected.
8
Welding current
Secondary voltage with welding current I
Rated supply voltage.
50- or 60-Hz single-phase power supply.
Max. absorbed current at the corresponding
current I and voltage U
2
This is the maximum value of the actual
current absorbed, considering the duty cycle.
Protection rating for the housing.
Grade 3 as the second digit means that this
equipment is suitable for use outdoors in
the rain.
Suitable for use
environments.
short-circuit between
Under these conditions the fan keeps
1
2
.
2
in high-risk
the welding
of the machine.