Technical Data; Before Starting The Equipment - EINHELL RT-TS 1725/1 U Originalbetriebsanleitung

Anleitung_RT_TS_1725_1_U_SPK1__ 20.11.15 06:51 Seite 27
hazards. It is also imperative to observe the accident
prevention regulations in force in your area. The same
applies for the general rules of health and safety at
work. The manufacturer will not be liable for any
changes made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossible
to eliminate certain residual risk factors. The following
hazards may arise in connection with the equipment's
construction and design:
Contact with the saw blade in the uncovered saw
n
zone.
Reaching into the running saw blade (cut
n
injuries).
Kick-back of workpieces and parts of workpieces.
n
Saw blade fracturing.
n
Catapulting of faulty carbide tips from the saw
n
blade.
Damage to hearing if ear-muffs are not used as
n
necessary.
Harmful emissions of wood dust when used in
n
closed rooms.

5. Technical data

AC motor
Power P
Idle speed n
0
Carbide saw blade
Number of teeth
Bench size
Table width extension, left/right
Table length extension, rear
Cutting height max.
Infinite height adjustment
Infinitely adjustable saw blade angle
Dust extraction connector approx. diameter
Weight
Operating mode S6
Rated operating period/rated idle period (4 min. on/6
min off)
To prevent the motor from overheating, only use the
bench-type circular saw as follows:
After an operating period of 4 minutes (S 6 = 40%)
under the permitted load, you must interrupt your
work for a period of 6 minutes in which the machine
can run idle.
Noise emission values
The noise emission values were measured in
accordance with EN 61029.
L sound pressure level
pA
K uncertainty
pA
L
WA
K
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors with
a potential influence on the actual immission level at
the workplace include the duration of impact, the type
of room, and other sources of noise etc., e.g. the
number of machines and other neighboring
operations. Reliable workplace values may also vary
230-240 V ~ 50Hz
from country to country. With this information the user
S6 40% 1700 W
should at least be able to make a better assessment
of the dangers and risks involved.
6500 min -1
Ø 250 x Ø 30
Reduce noise generation and vibration to a
24
minimum!
Use only equipment that is in perfect condition.
n
610 x 445 mm
Maintain and clean the equipment regularly.
n
608 x 250 mm
Adopt your way of working to the equipment.
n
435 x 320 mm Do not overload the equipment.
n
Have the equipment checked if necessary.
n
73 mm / 90°
Switch off the equipment when not in use.
n
63 mm / 45°
0 - 73 mm

6. Before starting the equipment

0° - 45°
Before you connect the equipment to the power
n
36 mm
supply make sure that the data on the rating plate
are identical to the supply voltage.
approx. 27 kg
Only ever connect the equipment to a properly
n
installed shock-proof socket which is protected by
a 10A fuse as a minimum.
Always pull out the power plug before making
n
adjustments to the equipment.
Unpack the bench-type circular saw and check it
n
for damage which may have occurred in transit.
Make sure the machine stands securely, i.e. bolt it
n
to a workbench or solid base.
sound power level
uncertainty
GB
Idle speed
94.9 dB(A)
3 dB
106.9 dB(A)
3 dB
27