Assembly - EINHELL RT-TS 1725/1 U Originalbetriebsanleitung

Anleitung_RT_TS_1725_1_U_SPK1__ 20.11.15 06:51 Seite 28
GB
All covers and safety devices have to be properly
n
fitted before the equipment is switched on.
It must be possible for the blade to run freely.
n
When working with wood that has been
n
processed before, watch out for foreign bodies
such as nails or screws, etc.
Before you actuate the On/Off switch, make sure
n
that the saw blade is correctly fitted and that the
equipment's moving parts run smoothly.

7. Assembly

Important. Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the circular saw!
7.1 Assembling the base frame (Fig. 4-9)
Turn the saw upside down and place it on the
n
floor.
Use hex screws (c) and washers (a) to fasten the
n
four legs (18) loosely to the saw (Figure 5).
Now loosely screw the longitudinal struts (20), the
n
cross struts (19) as well as the four center struts
(21, 22) to the legs using the hex screws (c),
washers (a) and nuts (b) (Fig. 6-7)
Be sure to secure the hex screws (c) and nuts (b)
n
only loosely.
Important: The longer struts have to be used on
the sides.
Now mount the four rubber feet (23) on the legs
n
(Figure 8).
Screw the stability bars (24) to the bore holes on
n
the rear legs using 2 hex screws (c), washers (a)
and nuts (b) on each side. (Figure 9)
Important.
Both stability bars must be fastened at the
mounting points 38 and 39 at the rear of the
machine.
Finally, tighten all screws and nuts on the base
n
frame.
7.2 Fitting the table width extension and length
extension (Fig. 10-14)
Loosely fasten the table width extension (14) and
n
length extension (15) to the saw table (1) using
the Allen screws (d) and the washers (u) (Fig. 10-
12). Use the rear holes (facing the table length
extension) to mount the table width extension.
Loosely screw the table supports (25, 26) to the
n
housing of the bench-type circular saw with the
hex screws (c) and washers (u). In addition the
table supports (25, 26) must be loosely screwed
to the width or length extension table with hex
screws (c), washers (a) and nuts (b). (Use the
short supports (25) for the width extension and
28
the long supports (26) for the length extension)
(Fig. 13-14).
Turn the saw together with the base frame and
n
place on the floor.
Align the table width extension and length
n
extension level with the saw table (1).
Finally, tighten all screws.
n
7.3 Fitting / removing the saw blade guard (Fig. 2,
15-16)
The batteries for the laser must be inserted prior
n
to initial assembly (see 9.9).
When assembling the equipment for the first time,
n
you must first fit and adjust the splitter (4). To do
so, proceed as described in Section 8.5.
Place the saw blade guard (2) together with the
n
screw (27) on top of the splitter (4) so that the
screw is snug in the oval hole (28).
Do not tighten the screw (27) too far – the blade
n
guard must be able to move freely.
Fit the extractor hose (3) to the extractor adapter
n
(16) and the extractor socket on the saw blade
guard (2) and secure it to the extractor adapter
(16) with the retaining clip (v). Connect a suitable
chip extraction system to the extractor adapter
(16).
To dismantle, proceed in reverse order.
n
Important.
The saw blade guard (2) must always be
lowered over the workpiece before you begin
to cut.
7.4 Changing the table insert (Fig. 17-18)
To prevent increased likelihood of injury, the table
n
insert (6) should be changed whenever it is worn
or damaged.
Take off the saw blade guard (2) (see 8.3).
n
Remove the 2 countersunk head screws (29).
n
Take out the worn table insert (6).
n
Fit the replacement table insert by following the
n
above in reverse.
7.5 Adjusting the splitter (Fig. 19-20)
Important. Pull out the power plug.
n
The setting of the saw blade (5) has to be
n
checked each time after changing the saw blade.
Set the blade (5) to max. cutting depth, move to
n
0° position and lock in place (see 9.2).
Dismantle the saw blade guard (2) (see 8.3).
n
Take out the table insert (6) (see 8.4).
n
Slacken the fixing screw (30).
n
Push up the splitter (4) until the gap between the
n
saw table (1) and the upper edge of the splitter
(4) equals approx. 10 cm.
The distance between the blade (5) and the
n
splitter (4) should be max. 5 mm. (Fig. 20).