Interruptions And Service An- Nouncements Control Circuit; Board; Brief Instructions For Maintenance And Servicing - Kärcher SB-Wash-E 10 Bedienungsanleitung

Adjustment control circuit

board

Menue point adjustment Option
Warm-Water Progr. 1 warm/ cold
Progr. 2
Progr. 3
Progr. 4
Time-Base Time-Base: 30...300 s
Wash-Time Progr. 0 100...50%
Progr. 1
Progr. 2
Progr. 3
Progr. 4
Progr. 5
Coin-Amount Channel 1: 10...200
Channel 2:
Channel 3:
Channel 4:
Channel 5:
Channel 6:
Options Halfload On/Off
Alloy wheel
Version Version: x.x
Statistics Coin Today: Coins
Counter Total: Coins
Timer Total: hours
HP-Pump S001: hours
S002: hours
Timer-Pro- Progr 1: hours
grams Progr.2: hours
Progr.3: hours
Progr.4: hours
Progr.5: hours
Error Error: Exxx
Message
Service Service:
Sxxx
*) Reset coin sum- daily counter: Push the "<" and ">" for two
seconds at the same time.
Brief instruction SB-WASH
Interruptions and service
announcements control
circuit board
Standard
setting
Display Cause
cold
E001 Set off the motor protection switch high pressure
warm
pump
cold
Winding protection contact motor
cold
E002 Fuse - F1 has triggered, circulating pump, heat fan
90 s
E003 Motor protection switch of the heater has triggered
100%
Temperature limiter 90°C triggered
60%
E100 Interruption control circuit
90%
70%
Servicecode Meaning
60%
S001 pump head HD-pump
60%
S002 HD-Pump totally
10
20
Menue navigation
40
40
80
120
On
Off
*)
button
OK, for 2 seconds
<, >
OK
ESC
EN
Intervall
250 h
500 h
Action
open the menue
change values, turn menue
confirm
cancel, exit
18
-
Brief Instructions
for maintenance and
servicing
Please pay attention to the section "maintenance and serv-
ice" in the operation instructions!
DAILY
Checl high pressure hose
check brush
Check information notices in the equipment
Check the pipe line and high pressure pump for tightness
Check the content of the cleaning agent container
DAILY IF FROST
Check and if needed clean the fan heater and the anti freeze cycle
After 40 operating hours, or weekly
Check oil level of the high pressure pump
Check the oil condition of the high pressure pump (is there water
in the oil?)
Clean the brush shaft and the floaing container
EVERY 14 DAYS
Clean and service the housing of the total equipment
After 160 operating hours, or monthly
Clean the coin mechanism.
Clean the filter of the cleaning agent container
Grease the joints at the doors
AFTER 250 OPERATING HOURS OR SEMI-ANNUALLY
Check pump head (Customer Service)
BEFORE THE FROST PERIOD
Check the anti freeze equipment of its function
BEFORE THE FROST PERIOD AND DURING THE FROST
PERIOD MONTHLY
Check the freezing water amount
After 500 operating hours, or yearly
Change the oil and high pressure pump
base exchanger (optional)
Pay attention to the saltusage, check daily
Refill the salt, if the water level is above the salt
Check salt container, remove sludge
The suction jet of the salt container must be put to the grounf of
the container
The gree light at the E-equipmentboard is blinking => base ex-
changer does regenerate
PROPORTION EQUIPENT HAS TO BE DECALCIFIED RM
110 (OPTION)
Pay attenetion to the amount used of the RM110, check daily
Red light at the E-equipment board => container empty
39