Kärcher SB-Wash-E 10 Bedienungsanleitung Seite 25

Setting the basic cleaning time
When changing the basic washing time, all
other washing programs are changed at
the same time.
 In the main menu select the function,
"time base".
 Ajust the basic washing time by pushing
the buttons „<"or „>" . the basic washing
time will be shown in units of seconds,
and can be adjusted by 10 second
steps between 30 and 300 seconds.
 Push the "OK" button to save the se-
lected value.
 Escape the function by pushing the
"ESC" button.
Adjustment by the manufacturer: Time-
Base: 90
Setting the washing time
The washing time of each cleaning pro-
gram can be between 50 and 100% of the
basic washing time.
 In the main menu select the function,
"wash-time".
 In the function menu selct the program
you want to adjust.
 Ajust the basic washing time ( in per-
centage of the basic washing time) by
pushing the buttons „<" or „>" .
 Push the "OK" button to save the se-
lected value.
 Escape the function by pushing the
"ESC" button.
Adjustment by the manufacturer:
Prog.0/OFF: 100
–
Prog.1: 60
–
Prog.2: 90
–
Prog.3: 70
–
Prog.4: 60
–
Prog.5: 60 (optional)
–
Setting the coin value
The coin value, as well as the coins, will tell
the different canals of the coin inspector,
how to evaluate them.
If the system is equipped with a Codax pin-
code input device, the coin values are set
for the different channels of the pincode in-
put device.
The value 10 is equal to a basic washing
process. The coin value between 10 and
200 can be adjusted by a 10 step selection.
 In the main menu select the function,
"Coin-Amount".
 Select each canal ("Channel") in the
function program.
 Ajust the coin value by pushing the but-
tons „<" or „>" .
 Push the "OK" button to save the se-
lected value.
 Escape the function by pushing the
"ESC" button.
Adjustment by the manufacturer:
Channel.1: 10
–
Channel.2: 20
–
Channel.3: 40
–
Channel.4: 40
–
Channel.5: 80
–
Channel.6: 120
–
Display operations data
 Push the „OK" 1 second – the selection
„Data Adjust" will be displayed.
 Push„>" – the main menue for the ad-
justments (data) will be displayed.
 Push the buttons "hans" and "hans" in
the main menu, and select „Statistics"
confirm with the „OK" button.
In the menu „Statistics" you may select for
the following counters:
Coin counter
Operation hours HD-
pump
Operating hours pro-
grammes
 Ajust the counter by pushing the but-
tons "hans" or "hans" .
For each counter you can select by pushing
the button ">" and ">" between a total coun-
ter and an subtotal counter.
Coin- Today Washing units since
Counter the last reset.
Total Washing units since
the installation
Timer Total Operating hours of the
Pump high-pressure pump
since the installation
S001 Operating hours high-
pressure pump since
the last maintenance
in 2001
S002 Operating hours high-
pressure pump since
the last maintenance
in 2002
Timer Prog.1 Operating hours of the
pro- respective programme
Prog.2
grams since start-up
Prog.3
Prog.4
Prog.5
Reset counter
The daily coin counter (Coin Counter, To-
day) can be reset by the operator:
 Display the coin counter „Coin-Coun-
ter", „Today" .
 Push the „<„ and „>" for two seconds at
the same time.
The operating hour counter "Service"can
only erased by the service. The total coun-
ter (Total) cannot be erased.
4
-
EN
Settings at the dosing pump
The dosing pumps are used to set the dos-
ing quantity of the detergent for individual
cleaning programmes.
Coin-Counter
Timer Pump
Timer pro-
grams
1 Dosing pump 4: hot wax
2 Dosing pump 1+2: high pressure wash,
brush wash
3 Dosing pump A (option): Alloy wheel
Dosing can be set from 3 to 70 ml/min of
detergent. Exact dosing depends on the
viscosity of the detergent used and the am-
bient temperature as well as the detergent
level and the erection site of the respective
container. Determine the exact values by
measuring the amount of detergent that
has been sucked in. Regulate accordingly
for lower ambient temperatures.
Standard setting
CHEM 1
CHEM 2
1 Cover
2 Rotary knob
 Lift the lid using a screwdriver.
 Set the rotary knob to the required val-
ue (see table below).
Position
1
2
3
4
5
6
7
8
 Replace the lid.
RM 806 ASF 19
RM 820 7
Suction quantity [ml/min]
3
7
19
28
37
48
60
70
3
2
25