Service Request; Maintenance Schedule - Kärcher SB-Wash-E 10 Bedienungsanleitung

Service request

If all rest value indicator do blink 3 times
continuesly, when turning the equipment
on, the service has to be performed. The
kind of service needed will be displayed at
the control circuit.
Display Service
S001 pump head HD-pump
S002 HD-Pump totally
The service should be done by Kärcher
specialists, otherwise the guarantee will be
invalid.
Time Activity
Daily Visible inspection of the high pressure
hoses
check brush
Check warning boards at the washing
place
Check the unit for leaks
Check filling level of the detergent.
Everyday un- Check frost protection devices
der frost condi-
Cleaning the sieve
tions
Clean the filter of the anti freeze pump. Clean the filter and replace
After 40 operat- Check oil level of the high pressure
ing hours or pump
Check oil level
once a week
Check the salt reserve in the salt con-
tainer (optional)
Check the level of the water softener
(optional)
Hardness of the water check ( by bse
exchanger option)
Clean the brush shaft
After 80 operat- Clean and maintain housing
ing hours or
once every two
weeks
After 160 oper- Clean the filter of the cleaning agent by
ating hours or using the cleaning agent cotainer.
Check the salt container ( by base ex-
once a month
changer optional)
Lubricate the door hinges
Oil the locks, doors , the control circuit
doors, and the coin container.
After 250 oper- Check pump head
ating hours or
Check the pump hose in the dosing
once every six
pumps
months
before the frost- Check frost protection devices
ing period
Before the check the anti freeze water amount at
frosting period the anti freeze cycle
and on monthly
basis during
the frosting pe-
riod.
After 500 oper- Check the high pressure pump thor-
ating hours or oughly
Oil change in high pressure pump
once a year

Maintenance schedule

Performance
Check high pressure hoses for mechanical damages such as scraping, visible hose duck,
bends, porous and cracked rubber. Replace damaged high pressure hoses.
concerning dirt, damage and waerout. If the bristles are shorter than 30mm, change them. In
the winter time, if it is –5 °C check several times a day besause of ice lock the foam washing.
Exchange the combi. steel pipe with the high pressure-steel pipe.
Check whether the warning boards for the users are available and legible.
Check pumps and pipes for leaks. Inform Customer Service if there is oil under the high pres-
sure pump, if more than 3 drops of water drop out of the high pressure pump when the pump
is running.
Check filling level, refill if necessary.
Is the hot air ventilator working? Is the anti freeze cycle functioning (anti freeze water amount
approximately 0,5 l/min)? Is the drain of the brush shaft to the swimming container free of ice?
Open the screw ( one top of the high-pressure pump), take out the strainer and clean it, put the
strainer back in, close the screws tight.
The oil level must lie between the MIN and MAX markings; else refill.
Milky oil indicates that it contains water. Inform Customer Service.
Is the salt level above the water level? If required, top up softening salts.
Check filling level; refill the softener RM 110, if required.
Take water from the fresh water container, and check the hardness by using the inspection set
B ( ording number: 6.768-003) . Target value: below 3 °dH
Remove the dirt from the brush shaft.
Clean the housing thoroughly from inside and outside. After cleaning conserve it with high
grade steel agent (ordering number: 6.290-911).
Remove filter and rinse it thoroughly with hot water.
Check water level (approx. 5 ... 25 cm above the sieve plate).
Check for deposits; if required, empty the tank, clean it, fill it up with softening salts and start it
up again. Risk of functional disturbances. While filling the softening salts, use only the softening
salt in the tablet form listed in the chapter "Accessories".
Lubricate the hinges with grease (order no.: 6.288-072).
Spray care liquid (order no. 6.288-116) into the locks.
Check the pump hose for cracks and wear; replace if required.
Change the freezing thermostat in the direction of "check", until the anti freeze equipment is
turned on. Fan heater and freezing cycle must start. If the temperature is above 5 °C in addition,
turn the thermostat of the fan heater up. Then turn the frost protection thermostat in an anti-
clockwise direction until the stop. Reset the thermostat of the hot air blower.
Note
The openings in the equipment socket may not be closed, otherwise the function of the anti
freeze thermostat is interrupted.
Target value: approx. 0.5 l/min
Water quantity is higher: Change the node piece in the hand-spray gun.
Water quantity is lesser Clean filter for frost protection pump; clean sieve in throttle, clean pipes,
check the rotation direction of the pump.
See Maintenance tasks
10
-
EN
By whom
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Operator
Customer Serv-
ice
Operator/Cus-
tomer Service
Operator
Operator
Customer Serv-
ice
Operator
31