Transport; Storage; Care And Service - Kärcher HD 6/15 MXA Bedienungsanleitung

3. Allow the device for run for a maximum of 1 minute
until the pump and lines are empty.
Note
Use commonly available, Glycol-based vehicle anti-
freeze. Observe the handling instructions of the anti-
freeze manufacturer.

Transport

CAUTION
Risk of injury, risk of damage
Be aware of the weight of the device during transporta-
tion.
ATTENTION
Risk of damage
Protect the trigger of the high-pressure gun from damage.
1. When transporting in vehicles, secure the device
against slipping and tipping over according to the
applicable guidelines.
2. Pull the device behind you via the push handle for
transporting over longer distances.
3. Pull the device step by step when ascending stairs.
The skids protect the casing from damage.
Transport retainer for surface cleaner
1. Plug the connection nozzle of the surface cleaned
onto the transport bracket on the high-pressure
cleaner.
2. Screw on the union nut by approximately 1 turn.

Storage

CAUTION
Risk of injury, risk of damage.
Be aware of the weight of the device during storage.
1. Store the device indoors only.

Care and service

DANGER
Risk of injury due to inadvertently starting up de-
vice and also due to electric shock.
Switch off the device immediately and unplug the mains
plug before performing work.
Safety inspection/maintenance contract
You can agree on regular safety inspections or close a
maintenance contract with your dealer. Please seek ad-
vice on this.
Each time before use
1. Check the power cable for damage and have a dam-
aged cable replaced immediately by the authorised
Customer Service or a qualified electrician.
2. Check the high-pressure hose for damage and re-
place a damaged high-pressure hose immediately.
3. Check the device for leaks. 3 drops of water per min-
ute are permissible. Contact Customer Service in
the case of more serious leaks.
Weekly
1. Clean the sieve in the water connection.
Clean the sieve in the water connection
1. Unscrew the union nut.
2. Pull out the hose union with sieve.
3. Externally clean and rinse the sieve.
Note: Align the hex-head of the hose union for con-
nection to the device.
4. Fit the hose union with sieve.
5. Tighten the union nut.
14
Every 500 operating hours, at least annually
1. Have the device maintained by Customer Service.
2. Changing oil.
Note
See the "Technical data" section for the oil volume and
type
1. Unscrew the 4 screws.
2. Remove the cover.
Figure E
3. Pivot the oil drain hose downwards over an oil catch
pan.
4. Pull the plug out of the oil drain hose.
5. Remove the cap.
6. Remove the foam from the oil tank.
7. Wait until the oil has drained completely.
Figure F
8. Insert the plug into the oil drain hose.
9. Pivot the oil drain hose upwards and latch in place.
10. Fill with the measured correct quantity of oil.
11. Insert the foam into the oil tank.
12. Fit the cap and press firmly in place.
Figure G
Replacing the high-pressure hose
WARNING
Risk of injury
The hose reel may turn very fast unexpectedly if it is re-
leased.
Carefully follow the steps below and secure the hose
reel as described.
1. Lift off the cover on the hose reel with a screwdriver.
Figure H
Cover
1
2. Completely unroll the high-pressure hose from the
hose reel.
3. Insert a 10 mm Allen key through the hexagonal
opening in the casing. Insert the key until the hose
reel is blocked.
Figure I
Opening, hexagonal
1
4. Unscrew the 2 screws.
Figure J
Screw
1
High-pressure hose
2
Hose stopper
3
5. Remove the hose stopper from the high-pressure
hose.
6. Pull out locking hook.
Figure K
Locking hook
1
Hose connection
2
High-pressure hose.
3
7. Pull high-pressure hose out of the hose connection.
8. Insert new high-pressure hose through the two hose
guide rollers and insert into the hose connection.
Observe the direction of rotation of the hose reel.
Figure L
Hose guide roller
1
English
Changing oil