Facom DT.VAG-A Bedienungsanleitung Seite 54

Disconnect the negative pole from the battery before starting work.
NB:
Before disconnecting the battery, make sure that the owner knows the code for the car radio.
Do not use the wedge pins to block the engine when unscrewing or tightening the crankshaft pulley.
Never use the belt as a holding tool to block or remove the camshaft pinion nuts.
Never exert pressure to force on the pulleys and rollers at the point where the distribution belt arrives in position.
Do not fold the belt or turn it inside out or bend it less than a 25mm radius.
Do not use lever or force to put a belt in place.
Check the belt idlers, stationary rollers and water pump through rotation.
Check the alignment of pulleys and rollers.
Check there is no oil leak or seepage. If so, remedy the problem.
When replacing the distribution belt, check that the new belt is fitted with the right kind of tooth.
Comply with the belt tension.
Comply with the tightening torques.
Comply with the rotation direction indicated by the arrows on the distribution belt.
Never re-install a worn distribution belt, but replace it.
Never re-stretch a distribution belt, but replace it.
Replace the belt if it shows signs of wear and tear - friction, cracking, damaged, cut, eroded or worn teeth, worn wall, worn edges or clogged with oil.
Any damage caused to the belt must be thoroughly investigated so as to define the causes before re-assembling a new belt.
Never use solvents (Diluent, petrol, etc.) to clean the oil deposits on the surface of the belt. In case of doubt replace the belt.
Any cleaning must be carried out with care using a soft, dry brush.
Never turn the belt inside out to clean it or for inspection.
Always run the engine in the normal rotation direction, failing contrary instructions from the maker of the vehicle.
DT.VAG-U
Engine Timing Tool Kit –
UPDATE TO USE IN CONJUNCTION WITH DT.VAG
Additional Tools for Timing Belt Replacement Applications and Chain Drive engines
VAG Diesel & Petrol Engines
Updating and increasing applications on Pumpe Düse diesels and 1.2 & 1.8 Petrol engines
UPDATED – Model/Engine Application Charts (DT.VAG + DT.VAG-U)
Section 2A: UPDATED - Diesel Engines TDi PD (Pumpe Düse)
Section 4A: UPDATED - Petrol Engines including Twin Cam
Section 5: UPDATED - Cross Reference to VAG Tool Numbers (DT.VAG + DT.VAG-U)
IMPORTANT: Always refer to the vehicle manufacturer's service instructions, or proprietary manual, to establish the current procedures
and data. This Product Information Set details applications and the use of the tools with any general instructions provided as a guide only.
Section 2A:
Pumpe Düse (Unit Injection)
DIESEL ENGINES – UPDATE Tools
1.9TDi PD diesels
Change to Mechanical Belt Tensioner - Refer to Application Chart for model usage
Up to 2002 all Pumpe Duse engines used a HYDRAULIC timing belt tensioner covered by tools supplied in DT.VAG Timing Kit – DT.4638 Tensioner Locking Tool and DT.4637 Tensioner Adjuster.
From 2002 Pumpe Duse engines started to be fitted with a MANUAL belt tensioner
New Tensioner Tool for Mechanical Tensioners – DT.4640T7 Tensioner Locking Pin
19
IMPORTANT: Belt tension adjustment must only be carried out when the engine IS COLD
Using DT.4637 Tensioner Adjuster, turn tensioner roller anti-clockwise until DT.4640T7 Locking Pin can be inserted. Then turn clockwise until it reaches a
"stop". Tighten roller nut and remove old belt.
Fit new belt, ensuring taut on non-tensioned side and that camshaft sprocket is in position within elongated slots.
20
Using DT.4637 Tensioner Adjuster, turn the tensioner roller anti-clockwise and remove DT.4640T7 Locking Pin. Then turn slowly clockwise until pointer
aligns with "notch".
Precautions
EN
54