Sabo 43-compact Betriebsanleitung Seite 41

Pos: 20.13 /Innenteil/Wartung des Motors/1.1 Kontrolle der Zündkerze (Abbildung Y ) @ 0\mod_1115369306250_1521.docx @ 1865 @ 2 @ 1
Checking the spark plug (Illustration Y )
Pos: 20.14 /Innenteil/Wartung des Motors/Kontrolle der Zündkerze Text 0,7mm @ 0\mod_1115369340031_1521.docx @ 1873 @ 2 @ 1
To check for wear, remove the spark plug connector and unscrew the spark plug. If the
electrode is badly worn the spark plug must be replaced as a matter of course. (Order
no. see original spare parts list and accessories).
Otherwise it is sufficient to clean the spark plug and set the electrode gap to 0.7 mm.
Screw the spark plug (pay attention to sealing ring) into the engine by hand and tighten
using the socket wrench. Press on spark plug connector. Replace the spark plug
annually.
Pos: 20.15 /Innenteil/Wartung des Motors/1.1 Vorschriftsmäßiges „Überwintern" des Motors (oder längerer Nichtgebrauch) @ 0\mod_1115369429437_1521.docx @ 1869 @ 2 @ 1
Correct winter storage of the engine (or when not used for a long period
of time)
Pos: 20.16 /Innenteil/Wartung des Motors/Vorschriftsmäßiges „Überwintern" des Motors Gerät kippen Text @ 0\mod_1115369463687_1521.docx @ 1878 @ @ 1
– Empty the petrol tank or allow the engine to run until it stops due to lack of fuel.
– Switch off engine and disconnect spark plug cable.
– Drain off the oil while the engine is still warm. Fill with fresh oil (for quantity and
type, see technical data).
– Clean grass and chaff from cylinder and cylinder head fins and around muffler.
– Always keep the machine in a clean condition in a closed, dry room out of reach of
children.
Pos: 21.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ 1 @ 1
Pos: 21.2 /Innenteil/Störungsursachen und deren Beseitigung/1 STÖRUNGSURSACHEN UND DEREN BESEITIGUNG @ 0\mod_1115373523343_1521.docx @ 1904 @ 1 @ 1
18 TROUBLESHOOTING
Pos: 21.3.1 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/1 Tabellenkopf @ 0\mod_1115374760156_1521.docx @ 1884 @ @ 1
Fault Possible cause
Pos: 21.3.2 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Motor springt nicht an E-Start 43er, 47er, 54er (fix speed) MUSTER @ 17\mod_1331727762233_1521.docx @ 134576 @ @ 1
Control handle not
Engine does not start
turned down.
up
Fuel tank empty.
Spark plug connector
loose.
Spark plug defective or
soiled or electrodes worn
out.
Too much petrol feed to
engine (spark plug wet).
Air filter soiled.
Battery not charged (only
for electro-start).
Start-up takes longer
than 5 seconds or is
repeated too often (only
for electro-start).
Connection cable
between the ignition key,
battery and engine is
loose or without contact
(only for electro-start).
Pos: 21.3.3 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Motorleistung lässt nach @ 0\mod_1127909215694_1521.docx @ 1896 @ @ 1
Air filter dirty.
Engine performance
decreases
Spark plug contaminated
with soot.
Pos: 21.3.4 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Motor läuft unregelmäßig @ 0\mod_1127909273145_1521.docx @ 1891 @ @ 1
Air filter dirty.
Engine runs irregularly
Spark plug contaminated
with soot.
Pos: 21.3.5 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Starke Erschütterungen (Vibrieren) @ 0\mod_1115377318234_1521.docx @ 1900 @ @ 1
Extreme vibration
Pos: 21.3.6 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Schnitt unsauber, Rasen wird gelb, Benzin @ 0\mod_1115377468656_1521.docx @ 1898 @ @ 1
Unclean cut, lawn is
yellow
Pos: 21.3.7 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Auswurf verstopft, Benzin, TurboSignal @ 0\mod_1127908095450_1521.docx @ 1886 @ @ 1
Ejection blocked
Remedy
Pos: 21.3.8 /Innenteil/Störungsursachen und deren Beseitigung/Störungstabellenelemente/Gemulchte Gras sieht schlecht aus Heckauswurf @ 5\mod_1183467132357_1521.docx @ 35950 @ @ 1
Mulched grass
appearance is poor:
Press the control handle onto
clumps, excessive
the upper part of the bar D .
clippings, rough cut.
Fill up with clean and fresh
fuel.
Push plug connector in place
or have it checked by an
authorised workshop.
Replace or clean spark plug,
set electrode distance to 0.7
mm Y .
Have it checked by an
authorised workshop.
Clean or replace air filter
insert W .
Charge battery W1 , X1 .
If you experience start
Pos: 21.4 /Innenteil/Störungsursachen und deren Beseitigung/Störungsursachen und deren Beseitigung Text Benzin @ 0\mod_1115378183390_1521.docx @ 1905 @ @ 1
difficulties, contrary to
In case of faults and defects which have not been listed here, please contact the
expectations, the battery
nearest authorized dealer.
must also be charged in
Repairs which require specialized knowledge should only be performed by a qualified
between.
expert. Your authorized dealer will naturally also be glad to help if you do not wish to
Connect the battery
perform the maintenance work described here yourself.
connector with the mating
Pos: 22.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
connector on the harness
U1 or check it or have it
checked by an authorised
workshop.
Clean or replace air filter
insert W .
Have it cleaned by an
authorized dealer.
Clean or replace air filter
insert W .
Have it cleaned by an
authorized dealer.
Have it checked by an
authorized dealer.
Have it checked by an
authorized dealer
11
Blade blunt. Have it sharpened and
balanced by an authorized
dealer Q .
Cutting height too low. Adjust to higher cutting height
I .
Engine speed too low. Operate at max. rpm.
Mowing too fast. Adjust mowing speed.
Insufficient overlapping Tall grass conditions may
of cuts when mowing. dictate that more overlapping
of cuts is required.
Lawn becomes matted. A lawn scarifier can remedy
the problem considerably
Turbo signal has not Empty the grass collector L .
been detected J + K .
Engine speed too low. Operate at max. rpm.
Cutting height too low for Adjust to higher cutting height
grass that is too high. I .
Pushing mower too fast. Adjust mowing speed.
Grass not dry. Let grass dry.
Blade blunt. Have it sharpened and
balanced by an authorized
dealer.
Mulching rule not Adjust to higher cutting height
followed (cut max. 1/3 of I .
the grass height; the
Convert mower to rear
height of the grass to be
discharge U2 + S1 and
cut must be lower than
mow grass first with higher
10 cm)
cutting setting.
Travel speed too fast. Adjust travel speed.
Grass build-up under Adjust to higher cutting height
deck. I .
Insufficient overlapping Tall grass conditions may
of cuts when mowing. dictate that more overlapping
of cuts is required
Grass not dry. Adjust to higher cutting height
I .
Let grass dry.